The System Setup menu

08

Subwoofer – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you want deeper bass (the bass frequencies that would normally come out the front and center speakers are also routed to the subwoofer).1 If you did not connect a subwoofer choose NO (the bass frequencies are output from other speakers).

AUTO – Adjust channel levels as the test tone moves from speaker to speaker automatically.

3 Confirm your selected setup option.

The test tones will start after you press ENTER.

DVD/LD

- 20.0dB

6b. Channel Level

 

P l e a s e W a i t . . . 2 0

L o u d t e s t t o n e s w i l l b e o u t p u t .

:Return

3Select ‘X. OVER’ and set the crossover frequency.2 Frequencies below this point will be sent to the subwoofer (or LARGE speakers).

4When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Channel Level

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system.

Important

When Channel Level is selected while MCACC is set to OFF, the selection screen for the MCACC memory appears. Select a memory to adjust manually.

DVD/LD- 55.0dB

6b. Channel Level

Select MCACC memory.

MCACC OFF

M1.MEMORY 1

ENTER:Next :Cancel

1Select ‘Channel Level’ from the Manual SP Setup menu.

DVD/LD

- 55.0dB

DVD/LD

- 55.0dB

6. Manual SP Setup

 

 

 

6b. Channel Level

 

 

 

 

 

 

 

MCACC : M1.MEMORY 1

 

a. Speaker Setting

Test Tone

 

 

 

b. Channel Level

 

 

 

 

AUTO

 

 

c. Speaker Distance

 

 

 

 

d. X-Curve

 

 

 

CAUTION

 

 

 

e . THX Audio Setting

 

 

 

 

:Return

ENTER:Next

:Return

4Adjust the level of each channel using the /

buttons.

If you selected MANUAL, use / to switch speakers. The AUTO setup will output test tones in the order shown on-screen:

DVD/LD

 

 

 

 

0.0dB

6b. Channel Level

 

 

MCACC

: M1.MEMORY 1

L

 

 

SR

[

0.0dB]

 

0.0dB

C

[

0

.0dB]

SBR [

0.0dB]

R

[

0

.0dB] SBL

[

0.0dB]

 

 

 

 

SL

[

0.0dB]

 

 

 

 

SW

[

0.0dB]

:Finish

Adjust the level of each speaker as the test tone is emitted.3

5When you’re finished, press RETURN. You will return to the Manual SP Setup menu.

Tip

The channel level can be changed at any time. Press

RECEIVER then press CH LEVEL on the remote control, and then use / to adjust the level.

Speaker Distance

For good sound depth and separation from your system, you need to specify the distance of your speakers from the listening position. The receiver can then add the proper delay needed for effective surround sound.

2Select a setup option.

MANUAL – Move the test tone manually from speaker to speaker and adjust individual channel levels.

Note

1If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in the amount of bass due low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.

2• This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.

If you’re using a THX speaker setup, confirm that the crossover frequency is set to 80Hz.

3• If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker to 75 dB SPL (C-weighting/slow reading).

The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.

51

En

Page 51
Image 51
Pioneer VSX-LX60 operating instructions Channel Level, Speaker Distance