Manuals / Planar / Computer Equipment / Projector

Planar PD7170 Performance, Microdisplay, Native Resolution, Aspect Ratios, Throw Ratios, Lamp

Models: PD7170

1 100

Download 100 pages 61.93 Kb

Page 94

Specifications

Table 7-1. PD7170 Specifications (continued)

	Performance

Microdisplay:	Texas Instruments DLP® 1280x720 DMD (x 3)

Native Resolution:	1280 x 720 (921,600 pixels)

Aspect Ratios:	Native (Pixel-to-Pixel), 16:9, Letterbox, 4:3,
	4:3 Narrow, Letterbox (Anamorphic lens
	compatible)

Projection Lens (Standard):	F/3.5, 25.5~32.0mm focal length

Throw Ratios:	Refer to Table 3-3

Vertical Lens Shift Range:	Up to 65% of screen height above or below lens
	center (130% of one half of the screen height)

Horizontal Lens Shift Range:	Up to 30% of screen width left or right of lens
	center (60% of one half of the screen width)

Video Lumens:	2,000 ANSI lumens (average) calibrated at D65

Sequential Contrast –	20,000:1 typical
DynamicBlack On:

Cooling Performance:	High efficiency adaptive voltage side-to-side
	cooling with low system acoustic noise level and
	low light pollution cabinet

Projection Modes:	Front, Rear, Ceiling (front/rear)

Lamp:	User replaceable, 230/260W HPM (selectable),
	2500 hour lifetime at 230W setting

Video Processing:	Planar customized Gennum GF9450 with 10 bit
	independent dual channel image processing,
	true 1080i deinterlacing, MPEG artifact reduction
	(block and mosquito noise), latest motion
	adaptive processing, 3D noise reduction, detail
	enhancement, rich color processing and noise
	reduction, less than one frame latency

Calibration:	Full RGB gain/offset control (White Balance),
	Gamma, Contrast, Color Temperature, Brightness

80	Planar PD7170 Installation/Operation Manual

Image 94

Planar PD7170 Performance, Microdisplay, Native Resolution, Aspect Ratios, Projection Lens Standard, Throw Ratios, Lamp

Contents

PD7170 Home Theater Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsXii List Of Figures List Of Figures About This Manual Carriage return must be used after each command orIntroduction Target AudienceUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsParts List Optional AccessoriesControls and Functions PD7170 at a GlanceExhaust Vent Planar Logo Badge Rear Cover PD7170 Rear Panel ComponentPD7170 Remote Control IR InputEnter PIP Controls and Functions Remote Control InstallationOperation IR Reception Angles Installation should be performed by a qualified custom Quick SetupInstallation Overview Video installation specialistInstallation Type InstallationProjector Installation Options ConsiderationsAmbient Light Throw DistanceVertical and Horizontal PD7170 Lens Options and Throw RatiosPosition Lens Shift Width, as shown in -4 and FigureVertical lens shift figures are for ceiling mount Folded OpticsLens Replacement Lens Motor Connector Trim RingMounting the PD7170 Connections to the PD7170Connector Panel Access Use the Hdmi inputs whenever possible. This ensures Highest video quality because the signal is carriedConnecting Source Components to the PD7170 Component output into the projectorRGB Connections Component Video Connections 10. Composite and S-Video Connections Connection RS-232 ControllerCommunications on Trigger Output to External Connecting 12-VoltConnecting an External IR Theater EquipmentConnecting to AC Power Turning on the Power Lens AdjustmentsFocus Zoom Lens Shift Changing the OSD Language Lens shift exceeds 50 per cent of the screen heightAdjusting the Picture Orientation Rear Projection Ceiling ModeInstallation Selecting an Aspect Ratio OperationSelecting Video Memory Selecting An Input SourcePIP Input Source Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations MainUsing the On-Screen Menus PD7170 OSD Menu Structure PIP source, switch to the PIP source thereby making it DynamicBlack to Off before adjusting Brightness, ContrastOther image quality settings in this menu refer to Active source, adjust the controls and then switchAspect Geometry of Projected Image Aspect Ratio Settings169 Letterbox Native You must enter a passcode to access the Save ISF Sub-menuTypical Pluge Pattern for Adjusting Brightness Change to the other in order to achieve the optimum setting Achieve the optimum settingBrightness and Contrast controls are interactive. a change Operation Crop Overscan ExamplesSource Select Sub-Menu Advanced PD7170 Advanced MenuOperation To the same frame rate as the main source X/y Color Gamut ValuesColor RGB Adjust Sub-Menu Generally, higher Gain settings reduce the image contrast Higher Offset settings reduce the image brightnessSome shimmer from a video or Hdtv source persists, use Adjust the Phase after adjusting Tracking see below. IfRemove high-frequency noise from the signal Noise Reduction controls described on page 46 toSystem 11. PD7170 System MenuDisabled If either Component 1 or Video is enabled, Scart must beIf Scart is enabled, both Component 1 and Video must be PIP 14. PIP Split-Screen Mode Control 15. PD7170 Control MenuOperation Language Service 16. PD7170 Service MenuOperation OSD menus are not available when in test pattern ModeMaintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution LED is flashing red PD7170 internal Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.brig Operations Commands Operations Control Commands Function Action on unitSerial Commands ValuesSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source PD7170 Specifications SpecificationsPD7170 Specifications Microdisplay Native ResolutionPerformance Aspect RatiosOperating Temperature DimensionsWeight without lens Universal Power SupplyPD7170 Dimensions 1shows the PD7170 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G Page Part No -0882-01 rev. a May