Manuals / Brands / Computer Equipment / Webcam / Proxim / Computer Equipment / Webcam

Proxim CPN 65755B HARD RESET TO FACTORY DEFAULT , FORCED RELOAD

1 121

Download 121 pages, 3.59 Mb

Tsunami MP.11and MP.11a Installation and Management

HARD RESET TO FACTORY DEFAULT

If you cannot access the unit or you have lost its password, you can reset the MP.11/a to the factory

default settings. Resetting to default settings means you must configure the MP.11/a anew.

To reset to factory default settings, press and hold the RELOAD button on the MP.11/a unit for about 10

seconds. The MP.11/a reboots and restores the factory default settings.

To access the MP.11/a see “Chapter 3. Management Overview” on page 19.

FORCED RELOAD

With Forced Reload, you reset the MP.11/a to the factory default settings and erase the embedded

software. Use this procedure only as last resort if the MP.11/a does not boot and the “Reset to Factory

Defaults” procedure did not help. If you perform a Forced Reload, you must download a new image file

with the Boot Loader (see “Image File Download with the Boot Loader” below).

Caution! The following procedure erases the embedded software of the MP.11/a. This

software image must be reloaded via an Ethernet connection with a TFTP server.

The image filename to be downloaded can be configured with either ScanTool

through the Ethernet interface or with the Boot Loader CLI through the serial port to

make the MP.11/a functional again.

To do a forced reload:

1. Press the RESET button on the MP.11/a unit; the MP.11/a resets and the LEDs flash.

2. Immediately press and hold the RELOAD button on the MP.11/a unit for about 20 seconds. Now

image and configuration are deleted from the unit.

3. Follow the procedure “Image File Download with the Boot Loader” to download an image file.

Chapter 7. Procedures 106

CPN 65755 Issue Date: August 2003

Contents

Main COPYRIGHT TRADEMARKS FCC COMPLIANCE Consult the dealer or an experienced radio or television technician for help. Contents Page Chapter 1. Overview WIRELESS NETWORK TOPOLOGIES ACTIVE ETHERNET Chapter 2. Installation IDENTIFYING NETWORK TOPOLOGY AND EQUIPMENT FINDING A SUITABLE LOCATION INSTALLING THE MP.11/a The Product Package One metal base for ceiling or desktop mounting (includes two screws) Mounting hardware One power supply One Tsunami MP.11/a Installation CD-ROM containing: Page Page Page Attaching a Kensington Security Lock (Optional) SWITCHING ON THE MP.11/a INSTALLING DOCUMENTATION AND SOFTWARE MOUNTING THE MP.11/a Desktop Mount Wall Mount Ceiling Mount Desktop Mounting Wall Mounting Ceiling Mounting Chapter 3. Management Overview MP.11/a IP ADDRESS Setting the IP Address Manually Dynamic IP Address with DHCP WEB INTERFACE OVERVIEW MP.11A OPTIONS Selecting a Country Dynamic Frequency Selection Transmit Power Control COMMAND LINE INTERFACE OVERVIEW Ethernet port connected through the network or with a cross-over Ethernet cable between the Serial port of the MP.11/a Ethernet Port Serial Port A serial RS-232C cable with a male and a female DB-9 connector. The serial cable must have a An ASCII terminal program, such as HyperTerminal. HyperTerminal Connection Properties Chapter 4. Basic Management REBOOTING AND RESETTING Applying Changes Rebooting Resetting Hardware Soft Reset to Factory Default Page SYSTEM CONFIGURATION Page IP CONFIGURATION INTERFACE CONFIGURATION Wireless Page Page Page Ethernet Port MONITORING SETTINGS Page SECURITY SETTINGS Encryption Passwords Changing the Telnet Password Changing the Web Interface Password UPGRADING THE MP.11/a Chapter 5. Web Interface STATUS Event Log CONFIGURE 1) System Page 2) Network IP Configuration DHCP Relay Agent Spanning Tree IP Routes 3) Interfaces Wireless Page Page Ethernet 4) SNMP 5) RIP There is no option to turn off receiving RIP advertisements. Once the unit is in Router mode, it RIP Example Page Page 9) Security MAC Authentication RADIUS Authentication Encryption Page Page Static MAC Pair Filtering Storm Threshold A maximum number of frames per second as received from a single network device (identified by its An absolute maximum number of messages per port. Broadcast Protocol Filtering IP Access Table ADDITIONAL INTERFACE INFORMATION Dynamic Frequency Selection (Tsunami MP.11a only) DFS Requirement Wireless Outdoor Router Protocol Satellite Density MONITOR 1) Wireless General WORP Page Page Page 7) Interfaces 8) IP ARP Table 9) IP Routes 10) Learn Table COMMANDS 1) Download Page 4) Reset 5) Help Link Chapter 6. Command Line Interface BOOT LOADER COMMAND LINE INTERFACE CLI TERMINOLOGY NAVIGATION AND SPECIAL KEYS COMMANDS ? (Question Mark) Done Command Download Command Exit Command Help Command History Command Log Command Passwd Command Quit Command Reboot Command Save Command Search Command Set Command CLI BASIC MANAGEMENT COMMANDS Page SHOW AND SET PARAMETERS Page Page Page Page Page Page Page Page Table Parameters Page Entering Strings Viewing Table Contents Creating a Table Row Modifying a Table Entry Modifying Several Table Entries Enabling, Disabling, or Deleting a Table Row COUNTRY CODE TABLE Chapter 7. Procedures TFTP SERVER SETUP WEB INTERFACE IMAGE FILE DOWNLOAD CONFIGURATION BACKUP CONFIGURATION RESTORE SOFT RESET TO FACTORY DEFAULT HARD RESET TO FACTORY DEFAULT FORCED RELOAD 3. Follow the procedure Image File Download with the Boot Loader to download an image file. IMAGE FILE DOWNLOAD WITH THE BOOTLOADER Download with ScanTool Download with CLI Page Appendix A. Specifications HARDWARE SPECIFICATIONS RADIO SPECIFICATIONS Channel Frequencies Appendix B. Troubleshooting LED INDICATORS MP.11/a CONNECTIVITY ISSUES MP.11/a Does Not Boot Serial Link Does Not Work HyperTerminal Connection Problems Ethernet Link does not work SETUP AND CONFIGURATION ISSUES Lost the MP.11/a Password The MP.11/a Responds Slowly No DHCP server is available. The IP address of the MP.11/a is already in use. There is too much network traffic. Web Interface Does Not Work Page Changes Do Not Take Effect Appendix C. Support and Contacts Glossary