02When mounting on a rack

Be sure to use the included rack mount brackets. Using anything else could damage this unit or result in injury. For details on mounting, see below.

•This unit has a rack mount size of 1U.

•The included rack mount brackets can be used to mount this unit onto an EIA 19-inch universal pitch or wide pitch rack.

Cautions on moving this unit

Moving this unit with an SD memory card inside could damage it. Stop data access to the SD memory card then eject the SD memory card before moving this unit. Also, press the STANDBY/ON button, check that the indicator switches from green to orange, then unplug the power cord. Unplugging the power cord before the indicator switches to orange could destroy the data on the SD memory card or restore this unit’s settings to their factory defaults.

•The STANDBY/ON indicator may remain lit for several dozen seconds after the power cord is unplugged. This is not a malfunction. Make sure the STANDBY/ON indicator has turned off before moving this unit.

Transporting this unit

When transporting this unit, be sure not to subject it to vibrations or shocks or to drop it. Do not let this unit be exposed to heat or water during transportation.

Be sure to remove any SD memory card before transporting this unit. Transporting this unit with an SD memory card in it could cause internal damage to this unit. Also, disconnect cables. Transporting with cables connected could damage the terminals.

Condensation

If this unit is moved suddenly from a cold place into a warm room (in winter, for example) or if the temperature in the room in which this unit is installed rises suddenly due to a heater, etc., water droplets (condensation) may form inside. When condensation is present, this unit will not operate properly and playback is not possible. Let this unit stand at room temperature for one or two hours with the power turned on (the time depends on the extent of condensation). When this unit is kept at room temperature, the water droplets will dissipate and playback will become possible.

Condensation can also occur in the summer if this unit is exposed to the direct wind from an air-conditioner. If this happens, move this unit to a different place.

Cleaning this unit

Normally, wipe this unit clean with a soft cloth. For tough dirt, apply some neutral detergent diluted in five to six parts water to a soft cloth, wring out thoroughly, wipe off the dirt, then wipe again with a dry cloth.

Note that getting alcohol, thinner, benzene or insecticide on this unit could cause the print and coating to peel off. Also, avoid leaving rubber or vinyl products in contact with this unit for long periods of time, as this could damage the cabinet.

When using chemical-impregnated wipes, etc., read the wipe’s cautions carefully.

Unplug the power cord from the power outlet when cleaning this unit.

Mounting on a rack

Caution

•The rack mount brackets included with this unit allow this unit to be mounted on universal pitch or wide pitch racks conforming to EIA 19-inch standards.

•The included rack mount brackets are exclusively for use with this unit. Never mount them on other devices or use them for other purposes; doing so is dangerous. Note that Pioneer will accept no responsibility whatsoever for any damages due to use of the rack mount brackets for other purposes, nor for any loss of business opportunities or other damages due to installation of this unit.

•Check that the rack has the appropriate strength for this unit’s weight and usage environment before mounting.

•The screws for fixing the rack mount brackets to the rack (indicated as * in page 29) are not included. Choose screws with the appropriate strength and length for this unit’s weight and usage environment to mount this unit on the rack. To ensure that this unit is fixed securely on the rack, be sure to fasten it with screws in all four rack mount screw holes.

•For the positions of the rack mount brackets’ mounting screw holes, see page 30.

•The mounting procedure should be performed by at least two people.

•When mounting, be extremely careful not to get your fingers, etc., caught between the rack mount brackets and the rack.

1Disconnect all cords connected to this unit (including the power cord).

Before starting, make sure there is no SD memory card in this unit.

2Mount the rack mount brackets.

Caution

•Be sure to use the included screws when mounting the rack mount brackets. Using any other screws could damage this unit or cause it to fall.

28

En