Hardware | Q-Logic 2300 instruction

Part I

Hardware

This part of the SANblade 2300 User’s Guide describes the host bus adapters (HBAs) and how to install and configure them. See the section that corresponds to your HBA. Section 4 contains troubleshooting information.

HBASection

QLA2340/2340L 2

QLA2342/2342L 3

FC2354601-00 A

I-1

Image 11

Q-Logic 2300 manual Hardware

Contents

SANblade 2300 Series User’s Guide Page Table of Contents Section QLA2342/2342L Part Software Section Windows NT Driver Installation Section NetWare Driver Installation FCode 10-4 Section Solaris Sparc Driver Installation FC2354601-00 a General Description How to Use this GuideWhat is Fibre Channel? Introduction Compliance with PCI Local Bus Specification revision Features Hardware Hardware FC2354601-00 a QLA2340/2340L HBA Components QLA2340/2340L Jumpers Installation in the ComputerLEDs QLA2340/2340L SunSPARC systems do not display the Bios banner Installation Help Introduction Configuration Settings Selectable Boot Settings Host Adapter Settings Raw Nvram Data Restore Default SettingsAdvanced Adapter Settings Setting Options Extended Firmware Settings Extended Firmware Settings RIO Operation Modes Select Host Adapter Scan Fibre Channel DevicesFibre Disk Utility Flashing a QLA2340/2340L HBA with FCode FCode New connection mode displays. For example Setting the QLA2340/2340L HBA Connection ModeConnection mode and options display. For example Type the following Setting the QLA2340/2340L HBA Loop IDSetting and Viewing the Fibre Channel Data Rate New loop ID displays. For example Ok show-devs Pci@1f,0/pci@1/QLGC,qla@4 Selecting the Boot Device Following displays Building the Bootable Disk Newfs -v /dev/rdsk/c3t130d0s0 Shut down the system. Type the following Boot from the newly created boot disk. For exampleView the current dump device setting. For example Tables 2-7and 2-8define the QLA2340/2340L specifications Specifications Conducted Emission LabelAgency Certification EMI and EMC Requirements Product Safety Requirements QLA2340/2340L Agency Certification FC2354601-00 a QLA2342/2342L HBA Components QLA2342/2342L QLA2342/2342L HBA LED Activity QLA2342/2342L Installation Help Fast!UTIL QLA2342/2342L Fast!UTIL Restore Default Settings Setting Options Extended Firmware Settings RIO Operation Modes Scan Fibre Channel Devices Flashing a QLA2342/2342L HBA with FCode Setting the QLA2342/2342L HBA Connection Mode Setting the QLA2342/2342L HBA Loop ID Selecting the Boot Device Building the Bootable Disk Newfs -v /dev/rdsk/c3t130d0s0 Shut down the system. Type the following QLA2342/2342L HBA Operating Environment Tables 3-7and 3-8define the QLA2342/2342L specifications QLA2342/2342L Label Product Safety Requirements QLA2342/2342L Agency Certification FC2354601-00 a System Configuration Problem Checklist TroubleshootingProblems After Installation Hardware Problem Checklist Fibre Channel Problem Checklist Operating System Software II Software II-2 FC2354601-00 a Windows NT Driver Files Windows NT Driver Installation QL2300.SYSWindows NT Installation Remove the disk, then click Yes to restart the computer Installing or Updating the Windows NT DriverClick OK Qldirect Updating the Windows NT Driver Updating to Qldirect from Qlfilter Qldirect InstallationInitial Installation of Qldirect Qldirect Driver Files Windows NT networking software must be installed QL2x00IP Ndis Network Driver InstallationInitial Installation of the QL2x00IP Ndis Network Driver Updating the QL2x00IP Ndis Network Driver Driver Configuration QL2x00IP Ndis Driver and IP Address Configuration IP Address Configuration Click Close Click Yes to restart the computer Removing the QL2x00IP Ndis DriverPage Creating the Driver Disk Windows 2000 Driver Installation QL2300.SYSWindows 2000 Installation Installing the Windows 2000 Driver Updating the Windows 2000 Driver Windows 2000 Driver Installation Windows Driver Installation QL2x00IP Ndis Network \W2k\Ip QL2x00IP Ndis Driver Configuration Adapter IP address Subnet mask255.255.0.0 Restart the computer Page Installing the Windows XP Driver Windows XP Driver Installation QL2300.SYS Installing Windows XP with the QLA23xx HBA as an Add-On Click Yes Installing the QL2300.SYS DriverClick Yes to continue with the installation Double-clickQLogic QLA2300 PCI Fibre Channel Adapter Updating the Existing QLA2300.SYS Driver MaximumSGList Removing the DriverSystem Registry Parameters Ql2300 Parameters Device CurrentControlSet Services Ql2300 Parameters DeviceNumberOfRequests FCTape UseSameNN Page NetWare Driver Files and Parameters NetWare Driver Installation QL2300.HAM Select Driver options from the main menu Installing the NetWare Driver Download the driver to the temporary directory Red Hat Linux Driver InstallationDriver Floppy Disk 1 New Operating System Installation Creating the Driver Floppy Disk Source Code Driver Floppy Disk Driver Floppy Disk 2 Installed Operating System Install or Update the Driver Installed Operating System Install a New Operating System and Driver Red Hat Linux To upgrade the existing qla2x00 drivers, type Installing the Driver on the Boot Drive # mcopy a*.tgz . The period . at the end is required Loading the Driver After line 338 add From the Main Menu, select Scsi support and press Enter Type the following command to access the Main MenuCreate a bootable kernel image by typing the following After line 609 add # cd arch/i386/boot # cp bzImage /boot/newsmp For a multiprocessor system, change the following line from Building a Ramdisk Image to Load the Driver Automatically Building a Ramdisk Image to Load the qla2300 Driver Loading and Unloading the qla2x00 Driver Manually Restart the system. The qla2300 driver loads automatically Loading and Unloading the qla2300 Driver ManuallyNew text is Building a Uniprocessor Version of the Driver Building a Driver from the Sources For Red Hat 7.1 and 7.2, type Building a Multiprocessor Version of the DriverFor Red Hat Linux 7.1 and 7.2, type # make dep Produces a file in the same directory called qla2300 Solaris Sparc Driver Installation QLA2300Installing the Solaris Sparc Driver from a CD-ROM You are prompted to select a driver package. For example At the command prompt, type pkgadd -d ./qla2300 Press Enter to accept the default 10.4