Vent Kits Components | Quadra-Fire QF130 manual

B. Vent Kits Components

Direct Vent Flex Liner Kits (see Figure 14.2)

LINK-DV-30B or (LINK-DV-30): Masonry 3 inch ﬂ ex liner

kit. Expands to 30 feet. Includes: two liners, termination cap, ﬂ ashing, and link adapter.

LINK-DV4-30B or (LINK-DV4-30): Masonry 3 inch ﬂex liner kit. Expands to 30 feet and 4 feet respectively. Includes: two liners, termination cap, ﬂ ashing, and link adapter.

LINK-DV-30B (LINK-DV-30)

LINK-DV4-30B (LINK-DV4-30)

Figure 14.2 Direct Vent Flex Liner Kits

Direct Vent Flex Liner Accessory Kits (see Figure 14.3)

Flash-Damp: Zero clearance damper ﬂ ashing kit for use with the LINK-DV-30B or LINK-DV4-30B liner kits.

LINK-ZC-ADP: Zero clearance chimney adapter

ÎDV-46DVA-GK: Adapter kit (colinear to coaxial 3 inches included in above kits). It is permissible to use DV-46DVA- GK to connect collinear ﬂ ex vent to SL-D vent pipe to extend the run.

FLEX3-30: One 3 inch ﬂ exible liner expands to 30 feet.

FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner, one connector per kit.

FLASH-DAMP

LINK-ZC-ADP

DV-46DVA-GK

FLEX3-30

FLEX3-CNCT

Figure 14.3 Direct Vent Flex Liner Accessory Kits

Î

40	Quadra-Fire • QFI30, QFI35 • 2227-900 Rev. H • 1/11

Image 40

Quadra-Fire QF130 owner manual Vent Kits Components, Direct Vent Flex Liner Kits

Contents

What to do if you smell gas ModelsHOT Surfaces Homeowner Reference Information CongratulationsXxxxxxxx Table of Contents User Guide Limited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear Space Control Module Operation Module ResetBefore Lighting Fireplace Lighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS Valve Issue Solutions Frequently Asked QuestionsAfter Appliance is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote Control Maintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionVenting Logs Burner Ignition and Operation IPI Pilot Flame Patterns Getting Started Typical Appliance System Tools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Fireplace Size Requirements Minimum Fireplace OpeningMinimum Fireplace Size QFI35 QFI30 Mantel and Wall Projections Side View TOP View Termination Locations Vent Termination Minimum Clearances Installation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting Components Placing, Securing and Leveling the Appli- ance IPI Models Installing Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit Optional Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements IntelliFire Plus Ignition System WiringON/OFF Switch Electrical Information Optional Accessories Requirements BLK Fan Wiring with Remote AUX 300 Module FAN WHT GRN BLK Blowers Finishing Clearances to Mantels or other Combustibles above Appliance Appliance Setup Log Set Assembly LOGS-QFI30 Models QFI30 Install the Log Assembly For LOG #6 Mates With Slot Mate Notch With Grate BAR Slot Log Set Assembly LOGS-QFI35 Models QFI35 Install Back Refractory Slot on Log #2 LOG Slot Mate LOG Pins with LOG Slots Flat Spot For LOG #6 Air Shutter Settings Air Shutter SettingQFI30 QFI35 Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System To remove any contaminants that may have accumulated on ﬂame Model Dimensions Appliance Dimension DiagramReference Materials Vent Kits Components Direct Vent Flex Liner Kits Contact Information