10 Electrical Information
A. Wiring Requirements
NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA
Code CSA C22.1.
•This appliance comes standard with a 120 VAC cord assembly which has a female plug in to accommodate all control options and accessories. See Figure 10.2. This is required for proper operation of the appliance (IntelliFire Plus Ignition). An outlet box may be installed in a bottom back corner of the existing solid fuel masonry or factory built fi replace to plug in the cord assembly, or the supplied power cord may be routed out onto the hearth to a nearby outlet.
•A 120 VAC circuit for this product must be protected with
•Low voltage and 120 VAC voltage cannot be shared within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire 120V to the valve or to the appliance wall switch. Incor- rect wiring will damage controls.
•An Intellifi re Plus™ Ignition System is standard with this appliance.
B. IntelliFire Plus™ Ignition System Wiring
•Wire an outlet box (120VAC) in the bottom back corner of the existing solid fuel masonry or factory built fireplace to plug in the cord assembly. The supplied cord assembly may also be routed out onto the hearth to a nearby outlet.
WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction box to a switched circuit. Incorrect wiring will override IPI safety lockout.
•Refer to Figure 10.1, IPI Wiring Diagram.
•This appliance is equipped with an IntelliFire Plus™ control valve which operates on a 6 volt/1.5 AMP system.
•Plug the 6 volt transformer plug into the cord assembly to supply power to the unit OR install 4 AA cell batteries (not included) into the battery pack before use.
ON/OFF Switch
•An ON/OFF switch is included with the appliance surround and should be attached to surround/facing. (See Installation instructions for remote control/fronts).
•If desired an additional wall switch or thermostat may be added to system as shown in Figure 10.1.
|
| INTERMITTENT |
|
|
|
|
|
| |
|
| PILOT IGNITOR |
|
|
|
|
|
| |
|
|
|
|
| RC100 | RC200 | RC300 |
| |
TO CORD ASSEMBLY |
|
|
|
| (OPTIONAL WALL CONTROLS) |
| |||
120VAC |
| MODULE |
|
|
|
|
|
|
|
|
|
|
|
|
|
| AUX2 NOT USED FOR INSERT MODELS. |
| |
|
| ORG |
|
| AUX300 MODULE |
|
|
| |
|
|
|
|
|
| PROTECTIVE COVER INCLUDED |
| ||
|
| WHT |
|
|
|
|
| ||
| FLAME |
|
| FAN |
|
| TO CORD |
| |
|
|
|
| AUX1 AUX2 |
|
|
| ||
MODULATION |
|
|
|
|
|
| |||
|
|
|
|
| ASSEMBLY |
| |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| (110V) |
|
|
|
|
|
| BATTERY PACK |
|
|
| |
|
|
|
| RED | 6V DC |
|
|
|
|
|
|
|
|
|
|
|
|
| |
ORANGE | GREEN | RED |
| BLK |
|
|
| ROCKER |
|
(PILOT) | (MAIN) | BLK |
|
|
|
|
| SWITCH |
|
|
| BROWN |
|
|
|
|
|
|
|
|
|
|
| WALL SWITCH |
|
|
|
| |
|
|
|
| OR REMOTE |
|
|
|
| |
|
| GROUND |
| INSTALL |
|
|
|
| |
Figure 10.1 IPI Wiring Diagram |
|
|
|
|
|
|
|
| |
|
| • | QFI30, QFI35 • | • 1/11 | 25 | ||||
