Chapter 2: The Remote Control
ON•OFF button
TV
TV button
DVD/VCR CABLE
SAT AUX AUDIO
ZOOM EDIT OPEN ANGLE
CLOSE
TIMER•GUIDE INFO
CLEARMENU
OK
AGAINADVANCE
Tips
The component button corresponding to the mode you’re in flashes when the remote batteries are low and you press a button on the remote.
To turn off most RCA components that are connected to the DVD/VCR, press ON•OFF twice within two seconds and hold the remote steady until the indicator turns off.
ON•OFF button
TV
TV button
DVD/VCR CABLE
SAT AUX AUDIO
Indicator light
ZOOM EDIT OPEN ANGLE
CLOSE
TIMER•GUIDE INFO
CLEARMENU
| OK |
|
AGAIN |
| ADVANCE |
| LIVE |
|
VOL |
| CH |
MUTE GO | ||
| BACK | |
1 | 2 | 3 |
4 | 5 | 6 |
7 | 8 | 9 |
INPUT | 0 | ANTENNA |
|
| PLAY button |
REVERSE | PLAY | FORWARD |
|
| REVERSE button |
RECORD | STOP | PAUSE |
STOP button
Find out if the remote can operate your TV
This remote control is designed to operate most RCA, GE, and Proscan TVs.
1.Press the TV button (if the TV turns on, this remote will operate your TV; if it doesn’t turn on, go to step 2 below).
2.Press the ON•OFF button (if the TV turns on or off, this remote will operate the TV).
3.If that doesn’t work, you can try programming the remote by following the instructions below.
Programming the remote to operate your TV
There are two ways to program this remote control to operate other brands of TVs: Direct Entry and Automatic Code Search (both methods are described below).
Direct Entry
1.Turn on the TV.
2.Look up the brand and code number(s) from the list that starts on page 25.
3.Press and hold the TV button on the remote.
4.Keep holding down the TV button, and enter the first code from the code list for your brand.
5.Release the TV button.
6.Point the remote toward the TV and press the ON•OFF button to see if the TV turns off. If it doesn’t, press the TV button and then press ON•OFF. If you get no response, follow these steps again, but enter the next code from the code list for your brand of television.
7.If you have tried all of the codes listed for your brand and this remote still doesn’t operate the TV, try the Automatic Code Search method (next section). If Automatic Code Search method doesn’t find the correct code, this remote won’t work with your TV and you’ll have to use the remote that came with your TV.
Note: This remote may not be compatible with all brands and models of televisions.
Automatic Code Search
The Automatic Code Search method for the TV button tests all of the TV codes. If you want to stop the automatic code search without programming the TV button to operate your TV, press CLEAR until the indicator on the remote turns off.
1.Turn on the TV.
2.Press and hold the TV button.While you continue pressing the TV button, press and hold the ON•OFF button until the TV button turns
3.Point the remote at the TV. Press and release PLAY, then wait 5 seconds or until the TV button stops flashing.
At this point the remote is searching for the correct code to program (you’ll know it’s found the correct code when the TV turns off, go to step 4). If, after 5 seconds, the TV doesn’t turn off, press PLAY again to tell the remote to search the next set of codes.
Continue pressing and releasing PLAY (at 5 second intervals) until the TV turns off or you have searched through all of the codes.The component buttons flash when all codes have been searched, the TV button turns off, and the remote exits Automatic Code Search.
4.When the TV turns off, the remote has found the proper code. Press and release REVERSE, then wait 2 seconds. Repeat this step until the TV turns back ON.
5.To finish, press and hold STOP until the TV button turns off.
•If you try all the codes for your TV brand and none work, the remote is not compatible with your TV.
22 | Graphics contained within this publication are for representation only. |
