Regency FG39-NG DURA-FLUE Horizontal Installations, Hint Apply silicone to female end, Diagram

INSTALLATION

945BG	45O Elbow-Swivel-Black
990	90O Elbow Galv.
990B	90O Elbow-Black
990G	90O Elbow-Swivel Galv.
990BG	90O Elbow-Swivel-Black
991	High Wind Term. Cap (Vertical)
980	Vertical Term. Cap
982	Snorkel-14" Rise Term.Cap
981	Snorkel-36" Rise Term.Cap

940Wall Thimble-Support/Box

941Cathedral/Ceiling-Support/Box

3951	Brass Trim-Wall Thimble/
	Ceiling Support

963Firestop Spacer

943Flashing 0/12-6/12

943S Flashing 7/12-12/12

953	Storm Collar
950	Vinyl Siding Standoff

988Wall Strap

942Wall Thimble

Parts not supplied by Dura-Flue 946-506/P Flue Guard (Optional) 948-128 Vinyl Siding Shield

Astro Cap (Australian)

DURA-FLUE

HORIZONTAL

INSTALLATIONS

1)Set the unit in its desired location. Check to determine if wall studs or roof rafters are in the way when the fluing system is attached. If this is the case, you may want to adjust the location of the unit.

2)Room Sealed pipe and fittings are designed with special twist-lock connections to con- nect the fluing system to the appliance flue outlet. A twist-lock appliance adaptor is installed on the unit at the fac-

tory. Assemble the desired combination of pipe and el- bows to the appliance adaptor with pipe seams oriented to- wards the wall or ceil-

ing, as much out of view as possible. The

final positioning of the pipe and 90o elbow as- sembly is deter- mined by the mounting orien-

tation of the adaptor on the stove and twist- locked for a sol- id connection.

Note:

a)Twist-lock procedure: Four indenta- tions, located on the female ends of pipes and fittings, are designed to slide straight onto the male ends of adjacent pipes and fittings, by orienting the four

pipe indentations so they match and slide in to the four entry slots on the male ends (diagram 1). Push the pipe sec- tions completely together, then twist- lock one section clockwise approxi- mately one-quarter turn, until the two sections are fully locked. The female locking lugs will not be visible from the outside on the Black Pipe or fittings. They may be located by examining the inside of the female ends. Apply sealant "Mill-Pac" to inner pipe and high temp silicone sealant to outer pipe on every twist-lock joint.

Hint: Apply silicone to female end.

b)Horizontal runs of flue must be support- ed every three feet. Wall straps are available for this purpose.

3)With the pipe attached to the stove, slide the stove into its correct location, and mark the wall for a 10" x 10" / 254mm x 254mm (inside dimensions) square hole. The center of the square hole should line up with the center-

Diagram 1

line of the horizontal pipe, as shown in diagram2.Cutandframethe10inch(254mm) square hole in the exterior wall where the flue will be terminated. If the wall being penetrated is constructed of non-combus- tible material, i.e. masonry block or con- crete, a 7" (178mm) diameter hole is accept- able.

Note:

a)The horizontal run of flue should have a 1/4 inch (6mm) rise for every 1 foot (.3m) of run towards the termination. Never allow the flue to run downward. This could cause high temperatures and may present the possibility of a fire.

Diagram 2

FG39: 59-3/4" (1518mm)

b)The location of the horizontal flue ter- mination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. For External Flue Termination Loca- tions, see diagram on page 8.

4)If installing the flue termination to a wall with vinyl siding, the Vinyl Siding Standoff must be used. Attach the Vinyl Siding Standoff to the Horizontal Flue Termination, but first run a bead of non-hardening mastic around its outside edges, so as to make a seal between flue cap and the standoff. Install the Vinyl Siding Standoff (Part # 950) be- tween the flue cap and the exterior wall and attach with the four wood screws provided. Seal around the Vinyl Siding Standoff on all four sides. Diagram 5. The arrow on the flue cap should be point- ing up. Insure that the 1-1/4" (32mm) clearances to combustible materials are maintained. See diagram 5.

Diagram 5

Note: If installing termination on a siding cov- ered wall, a vinyl siding standoff or furring strips must be used to ensure that the termination is not recessed into the siding. The four wood screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

5)Before connecting the horizontal run of flue pipe to the flue termination, slide the black decorative wall thimble cover over the flue pipe, then slide the Wall Thimble (Part # 942) over the flue pipe.

6)Slide the appliance and flue assembly to- wards the wall carefully inserting the flue pipe into the flue cap assembly. It is impor- tant that the flue pipe extends into the flue cap a sufficient distance so as to result in a minimum pipe overlap of 1-1/4 inches (32mm) . Secure the connection between the flue pipe and the flue cap using sheet metal screws provided. See diagram 6.

Regency FG39 FireGenie Freestanding Gas Stove 13