OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
1)Read and understand these instructions before operating this appliance.
2)Check to see that all wiring is correct and enclosed to prevent possible shock.
3)Check to ensure there are no gas leaks.
4)Make sure the glass in the door frame is properly positioned. Never operate the ap- pliance with the glass removed.
5)Verify that the venting and cap are unob- structed.
6)Ensure that the brick panels are installed.
7)Verify log placement. If the pilot cannot be seen when lighting the unit, the logs have been incorrectly positioned.
8)The unit should never be turned off, and on again without a minimum of a 60 second wait.
2)Turn gas control knob so indicator points to "OFF" position and allow 5 minutes for any gas in the combustion chamber to escape.
3)Turn gas control knob counterclockwise so indicator points to the "PILOT" position. Depress the gas control knob fully. Depress the igniter button several times until the pilot lights.After approximately one minute, release the gas control knob.The pilot flame should continue to burn. If the pilot does not remain lit, repeat operation allowing a longer period before releasing gas control knob.
4)When the pilot stays lit, turn the gas knob further counterclockwise to the "ON" posi- tion.
5)Use the wall switch, thermostat or remote control to turn on the unit.
6)Rotate the fl ame height regulator to adjust the fl ame height higher or lower.
SHUTDOWN
PROCEDURE
1)Use the wall switch, thermostat or remote control to turn off the main burner.
2)Turn the main gas control clockwise to the "OFF" position to turn off the pilot.
3)Turn off all electric power to appliance if service is to be performed.
DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE.
During the first few fires, a white film may develop on the glass front as part of the curing process. The glass should be cleaned or the film will bake on and become very difficult to remove. Use a
AERATION
ADJUSTMENT
The air shutter can be adjusted by moving the adjusting wire up or down.The wire is accessed through the bottom louver opening. Open the air shutter for a blue fl ame or close for a yel- lower fl ame. The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude.
Minimum Air Shutter Opening:
3/16" Natural Gas
1/2" Propane
CAUTION:Carbonwillbeproducedifairshutter is closed too much.
Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under warranty.
Note: AerationAdjustment should only be performedbyanauthorizedRegency Installer at the time of installation or service.
LIGHTING
PROCEDURE
IMPORTANT
To ignite or reignite the pilot, you must first release the ten- sion springs below the door.
Only when the pilot holds, without pressure being applied to the control knob, reapply the tension springs to the door. The unit must not be operated with the tension springs unattached.
IMPORTANT Gas cock knob cannot be turned from "PILOT" to "OFF" unless it is partially depressed.
1)Turn burner OFF using "ON/OFF" switch.
FIRST FIRE
The fi rst fi re in your stove is part of the paint cur- ing process. To ensure that the paint is properly cured, it is recommended that you burn your
fireplace for at least four (4) hours the fi rst time before you use it with the fan on.
When fi rst operated, the unit will release an odour caused by the curing of the paint, the burning off of any oils remaining from manufac- turing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a couple of hours.
The glass panel may require cleaning after the unit has cooled down. DO NOTATTEMPT
TO CLEAN THE GLASS WHILE IT IS HOT.
Note: When the glass is cold and the appli- ance is lit, itmaycause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.
Adjustment Wire: push to close or
pull to open aeration cap.
Closed - Tall yellow
Open - Short Blue
32 | UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace |
