Adjusting Bevel Lock, Marking the Ind-I-Cut | RIDGID Table Saw

Alignment (continued)

Marking the Ind-I-Cut:

a. With blade 90° (square to table) and miter gauge in left groove, cross cut a piece of wood holding the wood firmly against miter gauge.

b. Pull miter gauge back until freshly cut edge of wood is over disk. Using a sharp pencil, mark a line on disk at freshly cut edge of wood.

c. With miter gauge in right hand groove, follow same procedure and mark another line on disk.

d. These lines indicate the “path” of the cut (kerf) made by the sawblade.

e. When cutting the workpiece, line up mark on workpiece with line on disk.

NOTE: When the blade is changed, or a dado/molding head installed these lines can be erased and reset.

Marking

Ind-I-Cut

Using

Ind-I-Cut

Adjusting Bevel Lock

1.Release blade tilt lock lever and bevel blade to 45°.

2.Lock blade tilt lock lever, push in to dis- engage the outer hub of the elevation/ bevel handwheel and with moderate force attempt to move handwheel toward the 0° bevel.

3.If blade tilt mechanism cannot be moved, no additional adjustment is nec- essary.

4.If blade tilt mechanism can be moved adjust the blade tilt lock nut by rotating clockwise 1/4 turn.

5.Repeat steps 3 and 4 as necessary.

6.Release hub of the elevation/bevel handwheel and move blade tilt mecha- nism back to 0°.

Blade Tilt Lock Nut

32

Image 32

RIDGID Table Saw manual Adjusting Bevel Lock, Marking the Ind-I-Cut, Marking Ind-I-Cut Using, Blade Tilt Lock Nut

Contents

Page Table of Contents Safety Instructions For Table Saw Before Using The Saw Inspect your saw Reduce the Risk of Dangerous EnvironmentTo reduce the risk of injury from unexpected saw movement Inspect Your Blade Inspect your work area Safety Instructions For Table Saws Dress for safetyPlan your work Inspect your workpiece Reduce the Risk of Accidental Starting Keep Children AwayDon’t Force Tool Before freeing jammed material To reduce the risk of throwback of cut off pieces To remove loose pieces beneath or trapped inside the guardBefore Leaving The Saw Before Starting Glossary of Terms for Woodworking While Cutting Push Stick Push BlockRabbet Resin Motor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Wire Sizes Thermal Overload ProtectorThermal Overload Device Extension Gauge Cord Length Unpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Key Switch Table...provides working surface to support workpieces Sawdust Ejection Port Wrench/Blade Storage Rip Fence StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter Gauge Alignment Tools NeededRemove Foam Motor Support Checking Table Insert To check for parallelism Marked ToothSawbladeCombination Miter Gauge Square Groove Alignment Checking Blade Tilt, or Squareness of Blade to Table To Check For Squareness, 90 PositionIf blade is square to table Square Blade Pointer at Position Stopscrew Scale Screws Stopscrew To check for alignment, 45 PositionIf blade is 45 to table Pages Rip Scale Hold Down Adjusting Rip Fence Guide BarsAligning Rip Fence Guide Bars Combination Square Rip Fence Alignment AdjustmentAligning Sliding Table Extension Rip Fence Lock Lever Adjustment Adjusting Rip IndicatorAdjusting Nut Rip Indicator Installing Blade Guard If the sliding table extension moves when lockedChecking Sliding Table Extension Hex Locking Front Hex Nut Coupling Aligning Blade Guard WoodKerf Spreader Blade Do not loosen other screws. This Removing and Installing Sawblade Miter Gauge Alignment Adjusting Bevel Lock Marking Ind-I-Cut UsingMarking the Ind-I-Cut Blade Tilt Lock Nut Workbench Mounting Using Hardware Table Saw Mounting ProceduresFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your Saw Workbench Mounting Using C Clamps Supporting Table Saw with Sawhorses Safety Instructions for Basic Saw Operations Before Each Use Inspect your saw Plan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Stick Push Block For Use with Auxiliary Fence Auxiliary Fence Fence Facing Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations Crosscutting Repetitive Crosscutting Clamp Wood Block Cut Off Piece Compound Crosscutting Miter CrosscuttingBevel Crosscutting While Thru sawing Using the Rip FenceAdditional Safety Instructions for Rip Cuts Blade Path RippingOnce the trailing end is on the table Push Block Workpiece Auxiliary Fence Baffle Bevel Ripping Narrow WorkAuxiliary Fence Clamp Using Featherboards for Thru Sawing Might otherwise pinch the bladeKerf and cause a kickback Push Using Featherboards for Non-Thru Sawing Install blade guard immediately Using Carbide Tipped BladesResawing Kickback Dadoing Dado InsertSaw Arbor Rabbeting Ploughing and Molding Molding Molding Auxiliary Fence Maintaining Your Table Saw MaintenanceAdjusting Nylon Set Screw Ofadfa=oÉÅçããÉåÇë=íÜÉ=cçääçïáåÖ=ÅÅÉëëçêáÉë Trouble Probable Cause Remedy TroubleshootingGeneral Motor Trouble Probable Cause Remedy Repair Parts Parts List for Ridgid 10 Inch Table Saw Model No. TS24001 Always Order by Part Number not by Key Number Key Description Repair Parts Parts List for Ridgid 10 Inch Table Saw Model TS24001 Key Description 827483 Cover Blade Miter Gauge Assembly Always Order by Part Number Not by Key Number Description Fence Assembly Guard Assembly Page Page Page RIDGID, INC Stock No. TS2400 Model No. TS24001 Serial No