Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden CTHN-80 9 Reflector Installation, Hanger Burner Tube Reflector, Description

Models: CTHN-60 CTHN-150 CTHN-175 CTHN-80 CTHN-125 CTHN-40 CTHN-100 CTHN-200

1 48

Download 48 pages 22.1 Kb

Page 28

Step 8.9 Reflector Installation

CTHN-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL

Step 8.9 Reflector Installation

NOTE: All radiant tube surfaces must be covered by a reflector, except for a u-tube. Manifold tube may or may not be covered.

Hanger

Burner Tube

Reflector

Description	Part Number
Tube/Reflector Hanger	03090100

Burner Tube	03051XXX

Reflector	02750303

22

Image 28

Roberts Gorden CTHN-80, CTHN-200, CTHN-100 9 Reflector Installation, Hanger Burner Tube Reflector, Description, Part Number

Contents

Vantage NP CTHN-40 CTHN-60 CTHN-80 CTHN-100 CTHN-125CTHN-150 CTHN-175 CTHN-200 If you smell gasPage 2006 Roberts-Gordon,LLC TABLE OF CONTENTSPage TABLE OF FIGURES Page SECTION 1 HEATER SAFETY 1.1 Manpower RequirementsSECTION 2 INSTALLER RESPONSIBILITY 2.1 Wall Tag2.2 Corrosive Chemicals 2.3 National Standards and Applicable Codescombustibles at all times for safety FIGURE 1 STANDARD REFLECTORinches centimetersFIGURE 2 ONE SIDE REFLECTOR FIGURE 3 TWO SIDE REFLECTORSFIGURE 4 45 TILT REFLECTOR inchesFIGURE 5 U-TUBE,STANDARD REFLECTOR Modelinches A B C D UNAPPROVED centimeters A B C D UNAPPROVEDFIGURE 9 LOWER CLEARANCE SHIELD FIGURE 10 VENTINGModel inches4.1 Gas Codes 4.2 Aircraft Hangars4.3 Public Garages 4.4 ElectricalCTHN-Seriesburners may be used for unitary heaters or for multiburner systems Coupling Assembly with Lock Reflector Support Strap & Wire FormFan Assembly EP-300Series SECTION 6 MAJOR COMPONENTSSECTION 7 GENERAL SUSPENSION DETAILS FIGURE 12 Critical Hanger PlacementTypical Suspension Details Table 1 Contents of CTHN Burner Carton Table 2 Contents of Core and Extension PackagesTable 3 Component Package Guide Tubing LengthCore Packages Minimum8.2 Unitary Heater Requirements Table 5 Unitary Heater Design Requirements8.3 Unitary Linear Heater Layouts FIGURE 13 Linear Heater Assembly OverviewTube Clamp Package FIGURE 14 Unitary Linear Layout Overviews 60 18 m Tube Length FIGURE 16 U-tubeAssembly Overview 8.4 Unitary U-tubeHeater LayoutsFIGURE 17 Unitary U-tubeLayout Overviews Step 8.6 Tube Clamp Package Installation Step 8.5 Burner Tube InstallationWasher Step 8.7 Coupling and Tube Assembly Step 8.7.1 Coupling and Tube Assembly Continued± 2 5 cm Tighten slide bar as shown belowStep 8.7.2 Coupling and Tube Assembly Continued Step 8.8 Turbulator InstallationTurbulator Installation 2.3 mStep 8.9 Reflector Installation Hanger Burner Tube ReflectorDescription Part NumberPage Step 8.10 Burner Installation Step 8.11 Fan Inlet Plate and Warning TagDescription Part NumberStep 8.12 Restrictor Plate Installation Step 8.13 Fan InstallationDescription Part NumberTable 6 Contents of CTHN Burner Carton Table 7: Contents of Core and Extension PackagesTable 8 Component Package Guide Table 9 Common CTHN-SeriesComponentsCore Packages Minimum01326801 9.2 Multiburner System Design Requirements 9.3 Burners Per Pump Table 10 Multiburner Design RequirementsTable 11 Number of Burners Allowed Per Pump 9.5 Manifold Tube 9.4 Radiant Tube Length9.5.1 Manifold Diameter FIGURE 19 Flag Layout FIGURE 20 Modified In-SeriesLayoutMultiple rows of burners pump placed at the end of the manifold tubeFIGURE 21 T Layout FIGURE 22 Fork Layout FIGURE 23 Herringbone Layout Step 9.7 Burner Tube Installation Step 9.8 Tube Clamp Package InstallationBolt Tube ClampStep 9.9 Coupling and Tube Assembly Step 9.9.1 Coupling and Tube Assembly Continued± 2 5 cm Tighten slide bar as shown belowStep 9.9.2 Coupling and Tube Assembly Continued Step 9.10 Turbulator InstallationTurbulator Installation 2.3 mStep 9.11 Reflector Installation SECTION 9 MULTIBURNER HEATER INSTALLATIONHanger Burner Tube Reflector DescriptionEnd First Reflector U-clips Step 9.12 Burner Installation Burner must be installedSECTION 9 MULTIBURNER HEATER INSTALLATION window facing downSECTION 10 OPTIONAL HEATER ACCESSORIES Step 10.1.2 Elbow InstallationStep 10.1.3 Reflector Joint Installation Description