Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden CTHN-175 11 Reflector Installation, Hanger Burner Tube Reflector, Description

Models: CTHN-60 CTHN-150 CTHN-175 CTHN-80 CTHN-125 CTHN-40 CTHN-100 CTHN-200

1 48

Download 48 pages 22.1 Kb

Page 45

Step 9.11 Reflector Installation

SECTION 9: MULTIBURNER HEATER INSTALLATION

Step 9.11 Reflector Installation

NOTE: All radiant tube surfaces must be covered by a reflector, except for a u-tube. Manifold tube may or may not be covered.

Hanger

Burner Tube

Reflector

Description	Part Number
Tube/Reflector Hanger	03090100

Burner Tube	03051XXX

Reflector	02750303

39

Image 45

Roberts Gorden CTHN-175, CTHN-200 11 Reflector Installation, Hanger Burner Tube Reflector, Description, Part Number

Contents

CTHN-40 CTHN-60 CTHN-80 CTHN-100 CTHN-125 Vantage NPCTHN-150 CTHN-175 CTHN-200 If you smell gasPage TABLE OF CONTENTS 2006 Roberts-Gordon,LLCPage TABLE OF FIGURES Page 1.1 Manpower Requirements SECTION 1 HEATER SAFETY2.1 Wall Tag SECTION 2 INSTALLER RESPONSIBILITY2.2 Corrosive Chemicals 2.3 National Standards and Applicable CodesFIGURE 1 STANDARD REFLECTOR combustibles at all times for safetyinches centimetersFIGURE 3 TWO SIDE REFLECTORS FIGURE 2 ONE SIDE REFLECTORFIGURE 4 45 TILT REFLECTOR inchesModel FIGURE 5 U-TUBE,STANDARD REFLECTORinches A B C D UNAPPROVED centimeters A B C D UNAPPROVEDFIGURE 10 VENTING FIGURE 9 LOWER CLEARANCE SHIELDModel inches4.2 Aircraft Hangars 4.1 Gas Codes4.3 Public Garages 4.4 ElectricalCTHN-Seriesburners may be used for unitary heaters or for multiburner systems Reflector Support Strap & Wire Form Coupling Assembly with LockFan Assembly EP-300Series SECTION 6 MAJOR COMPONENTSFIGURE 12 Critical Hanger Placement SECTION 7 GENERAL SUSPENSION DETAILSTypical Suspension Details Table 2 Contents of Core and Extension Packages Table 1 Contents of CTHN Burner CartonTubing Length Table 3 Component Package GuideCore Packages MinimumTable 5 Unitary Heater Design Requirements 8.2 Unitary Heater RequirementsFIGURE 13 Linear Heater Assembly Overview 8.3 Unitary Linear Heater LayoutsTube Clamp Package FIGURE 14 Unitary Linear Layout Overviews 60 18 m Tube Length 8.4 Unitary U-tubeHeater Layouts FIGURE 16 U-tubeAssembly OverviewFIGURE 17 Unitary U-tubeLayout Overviews Step 8.5 Burner Tube Installation Step 8.6 Tube Clamp Package InstallationWasher Step 8.7.1 Coupling and Tube Assembly Continued Step 8.7 Coupling and Tube Assembly± 2 5 cm Tighten slide bar as shown belowStep 8.8 Turbulator Installation Step 8.7.2 Coupling and Tube Assembly ContinuedTurbulator Installation 2.3 mHanger Burner Tube Reflector Step 8.9 Reflector InstallationDescription Part NumberPage Step 8.11 Fan Inlet Plate and Warning Tag Step 8.10 Burner InstallationDescription Part NumberStep 8.13 Fan Installation Step 8.12 Restrictor Plate InstallationDescription Part NumberTable 7: Contents of Core and Extension Packages Table 6 Contents of CTHN Burner CartonTable 9 Common CTHN-SeriesComponents Table 8 Component Package GuideCore Packages Minimum01326801 9.2 Multiburner System Design Requirements Table 10 Multiburner Design Requirements 9.3 Burners Per PumpTable 11 Number of Burners Allowed Per Pump 9.4 Radiant Tube Length 9.5 Manifold Tube9.5.1 Manifold Diameter FIGURE 20 Modified In-SeriesLayout FIGURE 19 Flag LayoutMultiple rows of burners pump placed at the end of the manifold tubeFIGURE 21 T Layout FIGURE 22 Fork Layout FIGURE 23 Herringbone Layout Step 9.8 Tube Clamp Package Installation Step 9.7 Burner Tube InstallationBolt Tube ClampStep 9.9.1 Coupling and Tube Assembly Continued Step 9.9 Coupling and Tube Assembly± 2 5 cm Tighten slide bar as shown belowStep 9.10 Turbulator Installation Step 9.9.2 Coupling and Tube Assembly ContinuedTurbulator Installation 2.3 mSECTION 9 MULTIBURNER HEATER INSTALLATION Step 9.11 Reflector InstallationHanger Burner Tube Reflector DescriptionEnd First Reflector U-clips Burner must be installed Step 9.12 Burner InstallationSECTION 9 MULTIBURNER HEATER INSTALLATION window facing downStep 10.1.2 Elbow Installation SECTION 10 OPTIONAL HEATER ACCESSORIESStep 10.1.3 Reflector Joint Installation Description