Manuals / Roberts Gorden / Household Appliance / Electric Heater

Roberts Gorden TF-350 3 Tube Clamp Package Installation, 4 Coupling and Tube Assembly, Open

Models: TF-380 TF-250 TF-160 TF-200 TF-120 TF-300 TF-350

1 72

Download 72 pages 34.8 Kb

Page 28

Step 7.3 Tube Clamp Package Installation

TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL

Step 7.3 Tube Clamp Package Installation

		Tube Clamp	Bolt
	Flat
	Washer
	Nut
	(Torque
	120 in/lb
	13.56	Nm)
Description	Part Number
Tube Clamp Package	01318901
Tube Clamp	01396801
Bolt	97113940
Flat Washer	95211600
Nut	92113900

Step 7.4 Coupling and Tube Assembly

Close coupling	Start Slide bar/Coupling Lock
A with tab.	B onto coupling.

		Tab
			Slide Bar/Coupling Lock
			Wide End
			Coupling
	Open	3" (8 cm) to
		3" (8 cm) to
		4" (10 cm)
	Closed
	C Insert tubes into coupling.	D Tighten coupling to join tubes.
			Slide Bar/Coupling Lock
		Orient coupling so that	Coupling
		Orient coupling so that
		the impact block is in the
		2:00 or 10:00 o’clock
		positions.	Tube
		Tube
	Tube	Description	Part Number
	Tube	Coupling	01329600
		Coupling	01329600
		Slide bar/Coupling Lock	01329700
		Tube	91409XXX

22

Image 28

Roberts Gorden TF-350, TF-300, TF-120, TF-200 3 Tube Clamp Package Installation, 4 Coupling and Tube Assembly, Open, Closed

Contents

Installation, Operation & Service Manual Vantage TFTwin Fire Unitary Infrared Heater TF-120 TF-160 TF-200 TF-250 TF-300 TF-350 TF-380Page TABLE OF CONTENTS 2012 Roberts-GordonLLCPage TABLE OF FIGURES LIST OF TABLESPage SECTION 1: HEATER SAFETY 1.1 Manpower Requirements1.2 Safety Labels and Their Placement 1.3 California PropositionFIGURE 1: Top and Bottom Panel Label Placement Bottom PanelTop Panel Lighting Instruction Plate LabelFIGURE 2: Side Panel Label Placement Wiring LabelControl Side Panel Control Side Panel InsideSECTION 2: INSTALLER RESPONSIBILITY 2.1 Wall Tag2.2 Corrosive Chemicals Product Damage HazardClearances are the required distances that FIGURE 3: STANDARD REFLECTOR inchescentimeters ModelFIGURE 6: 45 TILT REFLECTOR inchescentimeters ModelFIGURE 9: U-TUBE,OPPOSITE 45 REFLECTOR inchescentimeters ModelFIGURE 12: VENTING Model4.1 Gas Codes 4.2 Aircraft Hangars4.3 Public Garages 4.4 ElectricalCoupling Assembly Flexible BootReflector Support Strap & Wire Form SECTION 5: MAJOR COMPONENTSTable 1: Contents of Burner Carton 5.1 Standard Parts ListTable 2: Contents of Core and Extension Packages Additional tubing length may be added to heater. Tubing must be heat-treated,aluminized or porcelain coated. Any additional tubing lengths are considered as vent length for length determination. Maximum venting length for minimum heater length is 45 13.7 m total, or 22.5 7 m on each tube SECTION 6: SUGGESTED LAYOUTS 6.1 TF-380- 4 Elbow Design Common Vent6.2 TF-350- 4 Elbow Design Common Vent 6.3 TF-300- Double U Design Common Vent10 Typ 90 ElbowBurner TubeSECTION 7: HEATER INSTALLATION Severe Injury Hazardon Page 17, Figure Cut/Pinch HazardFIGURE 14 Critical Hanger Placement Typical Suspension DetailsFIGURE 15: Linear Heater Assembly Overview FIGURE 16: Linear Heater Layout Overview LEGEND70 21 m Tube Length Each Side 60 18 m Tube Length Each Side80 24 m Tube Length Each Side Step 7.1 Burner Tube Installation Step 7.2 Burner InstallationStep 7.3 Tube Clamp Package Installation Step 7.4 Coupling and Tube AssemblyOpen ClosedStep 7.4.2 Coupling and Tube Assembly Continued Step 7.4.1 Coupling and Tube Assembly Continued± 2 5 cm Step 7.5 Turbulator Installation Fire Hazard 7.6 Reflector InstallationReflector must not touch tube To ensure proper expansion and contraction reflector supports and U-clipsdepends on theSECTION 8: OPTIONAL HEATER ACCESSORIES 8.1 U-TubeConfigurationCut/Pinch Hazard Edges are sharpFIGURE 18: U-TubeHeater Assembly Overview U-tube,StandardU-tube,45 U-tube,OppositeFIGURE 19: U-TubeHeater Layout Overview LEGENDFIGURE 20: U-TubeHeater Layout Overview Continued bc gd h8.2 Elbow Package Configuration Step 8.2.1 Elbow InstallationStep 8.2.2 Elbow Installation Step 8.2.3 Reflector Joint InstallationStep 8.2.5 Reflector Joint Detail Step 8.2.4 Reflector Joint InstallationFIGURE 21: Reflector Joint Detail Step 8.3.2 Side Reflector Installation Step 8.3.1 Bracket Installation8.3 Reflector Side Extension 8.4 Lower Clearance Shield Installation Step 8.4.1 Shield Support Strap Assembly8.5 Two-FootDecorative Grille Installation Step 8.5.1 Grille InstallationStep 8.5.2 Frame Shield Installation Part NumberMinimum Maximum8.6 Protective Grille Installation Step 8.6.1 Silicone Cap InstallationStep 8.6.2 Grille End Cap Installation Step 8.6.3 Grille InstallationSECTION 9: VENTING Carbon Monoxide HazardCut/Pinch Hazard Edges are sharp9.4 Vertical Venting 9.5 Unvented Operation Tube TerminationFIGURE 22: Tube Termination 9.6 Length Requirements9.9 Flexible Boot Installation Single Vent 9.8 Vertical Ventilation 4 10 cm PipeSIDE VIEW for Single Vent9.10 Common Sidewall Venting 9.11 Vertical Ventilation 6 15 cm PipeTOP VIEW Roof9.12 Flexible Boot Installation Common Vent Rolled Sleeve Installation for Common Vent9.13.2 Vertical Outside Air Supply 9.13 Outside Combustion Air Supply9.13.1 Length Requirements 9.13.3 Horizontal Outside Air Supply Metal ScrewsGas hose can crack when twisted Gas can leak if piping is not installed properlySECTION 10: GAS PIPING Fire Hazardwhen attaching gas hose INCORRECT POSITIONS WRONG INSTALLATIONFIGURE 23: Gas Connection with Flexible Gas Hose CORRECT POSITIONSDANGER SECTION 11: WIRINGDisconnect electric before service 11.1 Line Voltage Thermostat Wiring11.2 Low Voltage Thermostat and Relay Wiring 11.3 Internal Wiring 11.4 Ladder DiagramElectrical Cord or Flexible Conduit Burner SECTION 12: OPERATION AND MAINTENANCE heater before servicebefore service during installation12.5 Maintenance Checklist Installation Code and Annual InspectionsSee Page 5, Section Vehicles and Other ObjectsSafety Labels Gas LineCheck for gas leaks. See Page 44, Section Burner ObservationSECTION 13 TROUBLESHOOTING Disconnect electric before serviceheater before service before serviceg Flow Chart 13.1 TroubleshootinTROUBLESHOOT ENDS 13.2 Manifold Gas Pressure Setting Control Side View of HeaterManometer NaturalPropaneSECTION 14: REPLACEMENT PARTS DANGERDescription Part NumberSECTION 15: GENERAL SPECIFICATIONS 15.1Material Specifications 15.1.1 Reflectors15.2Heater Specifications 15.2.1 Ignition 15.3 Suspension SpecificationsPage WARRANTY IS VOID IF ROBERTS-GORDONLLC WILL PAY FORROBERTS-GORDONLLC WILL NOT PAY FOR LIMITATIONS ON AUTHORITY OF REPRESENTATIVESPage Page Page