Manuals / Roberts Gorden / Household Appliance / Gas Heater

Roberts Gorden UHA[X][S] 45 Description, Part Number, Wall Shelf Mounting Bracket Kit

Models: UHA[X][S] 75 UHA[X][S] 60 UHA[X][S] 100 UHA[X][S] 125 UHA[X][S] 30 UHA[X][S] 45

1 62

Download 62 pages 51.32 Kb

Page 18

Image 18

UHA LOW PROFILE UNIT HEATER INSTALLATION OPERATION AND SERVICE MANUAL

Figure 7: Wall Shelf Mounting and Hanging Suspension

Description	Part Number	Qty.
Wall Shelf Mounting Bracket Kit	12011002K
Wall Suspension Mounting Bracket Kit	12011001K	1
Shelf Mounting Bracket Kit	12011000K	1

Description	Part Number	Qty.
Wall Suspension Mounting Bracket Kit	12011001K
Wall Mounting Bracket Arm Left	111WALL1L	1
Wall Mounting Bracket Arm Right	111WALL1R	1
Wall Mounting Bracket Vertical	111WAL2	2
Wall Mounting Bracket Diagonal	111WAL3	2
5/16" x 3 1/2" Bolt	97213925	6
5/16" Lock Nut with Nylon Insert	92114000	6
5/16" Flat Washer	95211600	6
5/16" Lockwasher	96411600	6

Hardware provided to construct mounting bracket assembly only.

Page 18

Image 18

Roberts Gorden UHA[X][S] 45, UHA[X][S] 30, UHA[X][S] 125 Description, Part Number, Wall Shelf Mounting Bracket Kit

Contents

UHA-Series Tubular Unit Heaters Low Profile Range Installation, Operation & Service ManualCombat Models UHAXS 30, 45, 60, 75, 100,Page TABLE OF CONTENTS 2008 Roberts-GordonLLCPrinted in U.S.A Page TABLE OF FIGURES Page SECTION 1: HEATER SAFETY 1.1 Manpower Requirements1.2 Safety Labels and Their Placement Figure 1: UHA 30 - 45 Label Placement For separated combustion units only Figure 2: UHA 60 - 75 Label Placement For separated combustion units only Figure 3: UHA 100 - 125 Label Placement For separated combustion units only 2.2 Corrosive Chemicals SECTION 2: INSTALLER RESPONSIBILITY2.1 Wall Tag 2.3 National Standards and Applicable Codes 3.5 Clearances to Combustibles 3.4 Minimum Required Installation Clearances3.2 Manufactured Units 3.6 Ventilation 3.7 Gas Supply 3.8 Electrical Supply3.9 Vent 4.3 Parking Structures and Repair Garages 4.1 Gas Codes4.2 Aircraft Hangars 4.4 Electrical 4.6 High Altitude 5.3 Wall Mounting SECTION 5: MAJOR COMPONENTS 5.1 General5.2 Shelf Mounting and Suspension Crush Hazard Use 3/8 threaded rod minimum Figure 5: Suspension Methods Figure 6: Shelf-MountingMethodsExisting cabinet screws must be re-used Wall Shelf Mounting Bracket Kit DescriptionPart Number Description louver and compress Figure 8: Vertical Louvers OptionalPush in spring to remove 6.1 Changing Vent and Air Intake Orientation 6.3 Vent InstallationSECTION 6 VENTING 6.2 Venting 6.3.1Standard Vented Heaters Models UHAX 30 - 6.4 Unvented Operation6.5 Horizontal Venting 6.7.1 Maximum Vent Lengths 6.6 Vertical Venting6.7 Length Requirements 6.8 Vent Material Horizontal Figure 9: Vent and Roof DetailVertical OptionPage Horizontal Figure 13: Concentric Vent BoxVertical Option Option Vent Terminal SECTION 7 AIR SUPPLY 7.1 Separated Combustion Installation7.2 Unvented Installation 7.3 Building Ventilation SECTION 8: GAS PIPING 8.1 ConnectionsFigure 15: Gas Connection 9.1.1 Fan Control SECTION 9: WIRING9.1 Positioning Thermostats 9.2 Low Voltage Thermostat with One Heater Relay Part Number ModelRelay Type UHAXS 30 - 90436300 UHAXS 60 -DPST Max. Number of Heaters 9.5 Internal Wiring Diagram 9.6 Ladder Wiring Diagram 9.7 Electrical Connection to the Heater 10.1.1 Louvers SECTION 10: OPERATION AND MAINTENANCE10.1 Pre-Start-UpChecks 10.1.2 Electrical Checks Required Incoming Signals Figure 16: Automatic Burner Control SequenceFigure 17: Gas Valve for Models UHAXS 30 - Signals Output By Control Check Gas Rate 10.2.3 Pressure SwitchFigure 18: Gas Valve for Models UHAXS 60 - 10.2.4 Turning Off the Heater 10.2.5 External Controls 10.3 Complete Start-Up10.3.1 Instruction to the User SECTION 11: USER INSTRUCTIONS Reset Limit Switch - See Page 33, SectionFigure 19: Manual Reset Limit Switch 11.1 User Instructions Figure 20: LED Diagnostic Codes 11.5 Simple Troubleshooting11.5.1 Simple Troubleshooting Burner Faults 11.4.2 To Turn the Heater Off 12.4 Heat Exchanger Maintenance 12.2 Burner Maintenance12.3 Fan/Motor Assembly Maintenance 12.5 Gas Valve Maintenance The Vicinity of the Heater 12.8 Maintenance Checklist12.7 Venting and Air Intake Pipe See Page 6, Section Pipe when installedCombustion Air Intake Heat Exchanger SECTION 13: TROUBLESHOOTING 13.1 General START SECTION 13: TROUBLESHOOTING 13.3 Troubleshooting for Flame Supervision System Correct power 13.4Troubleshooting for Gas Valves13.5Troubleshooting for Flue Blower START SECTION 14 REPLACEMENT PARTS Burner Components14.1 Gas Valve 14.2 Burner Compartment 14.2.1 Burner Injectors 14.3 Ignition Electrode and Flame Probe Install Vertical screws 14.4 Heat Exchanger14.5 Louver and Louver Springs Horizontal 14.6 Flue Blower Vertical Installation 14.7 Pressure Switch 14.9 Axial Fan/Guard/Motor Assembly14.8 Ignition Control 14.10 Limit Switches 14.9.1 Fan Removal and Replacement14.9.2 To Replace the Fan Assembly 14.10.1 Removal and Replacement SIDE VIEW SECTION 15: SPECIFICATIONS 15.1 Dimension DataTOP VIEW REAR VIEW 15.2 General Technical Data Table All Models 15.3 Technical Data Table All Models ROBERTS GORDON WILL NOT PAY FOR WARRANTY IS VOID IFROBERTS GORDON WILL PAY FOR Roberts-GordonPage Purchased From if different than installer OWNER WARRANTY REGISTRATION CARDAbout the Installer Type of Installation check onePage Page close to heater Installation ClearancesFire Hazard injury or property damage