98RR-1050
5.Fšr att skapa en tidsfšrdršjning efter ett kommando, hŒll ned knappen i šnskad tidslŠngd som fšrdršjningen skall vara.
6.NŠr hela makrosekvensen Šr inmatad tryck pŒ LEARN- knappen fšr att avsluta programmeringen. Texten ÓMAR.OKÓ visas i displayen som bekrŠftelse pŒ att det Šr avslutat.
Den senast valda Enhets-knappen i makrot Šr den gŠllande som RR-1050 Šr instŠlld pŒ att styra. Om man vill att en annan Enhets-knapp skall vara gŠllande efter anvŠndning av ett Makro-kommando, sŒ vŠlj den knappen som sista steget i makro-sekvensen.
Radera lagrade kommandon ![](/images/new-backgrounds/1247407/2474079xi2.webp)
CLEAR-knappen raderar inlŠrda kommandon frŒn en enskild knapp, alla kommandon pŒ en Enhets-knapp eller en Makro-sekvens.
1.Tryck pŒ den nedsŠnkta CLEAR-knappen med spetsen pŒ en kulpenna. ÓCLEAR?Ó visas i displayen.
2.Tryck pŒ en kommando-knapp fšr att radera ett enskilt kommando. Tryck pŒ en Enhets/IngŒngs-knapp i mindre Šn en sekund fšr att radera kommandot fšr enhetsval. Tryck och hŒll ned samma knapp fšr att radera kommandot fšr ingŒngsval. Tryck pŒ MACRO- knappen fšljt av knappen som makrot Šr lagrat pŒ fšr att radera makro-sekvensen. Raderingen bekrŠftas med ÓOK!Ó i displayen.
OBS! NŠr ett programmerat kommando raderats pŒ en Enhets/IngŒngs-knappen ŒtergŒr knappen till den fabriksprogrammerade koden.
RR-1050 lŠmnar automatiskt raderings-lŠget, ÓCLEARÓ, om ingen knapp tryckts pŒ 15 sekunder. Man kan manuellt gšra detta genom att trycka pŒ CLEAR-knappen igen.
FabriksinstŠllning ![](/images/new-backgrounds/1247407/2474079xi3.webp)
Tryck pŒ den nedsŠnkta PRELOAD-knappen med spetsen pŒ en kulpenna fšr att lŒta RR-1050 ŒtergŒ till fabriksprogrammerat tillstŒnd. Texten ÓLOADINGÓ visas i displayen under tiden som fabrikskoderna ŒterstŠlls. NŠr detta Šr klart visas ÓOK!Ó i displayen.
OBS! Genom att trycka pŒ PRELOAD-knappen raderas alla inlŠrda kommandon pŒ AUD- och V1-knapparna. Fabriksprogrammeringen ŒterstŠlls till Rotels receivrar, surroundprocessorer och DVD-spelare.Var sŠker pŒ att det Šr detta du vill gšra! Kommandon pŒ de andra knapparna raderas inte.
English 7
Here is the layout of the RR-1050:
IR Emitter/Sensor ![](/images/new-backgrounds/1247407/2474079xi4.webp)
The IR Emitter/Sensor is located in the top edge of the RR-1050. It sends the IR commands and must be pointed at the desired component. It also receives IR codes from your other remote controls during the LEARNING process.
LCD Display ![](/images/new-backgrounds/1247407/2474079xi5.webp)
The LCD DISPLAY provides information including the de- vice selected and the input you have selected. The eight character alphanumeric display also provides simple prompts when programming the RR-1050. These indica- tors and prompts are noted in the appropriate sections of this manual.
In addition, the display shows a customizable label when a button is pressed.
Light Button
and Light Sensor ![](/images/new-backgrounds/1247407/2474079xi7.webp)
The RR-1050 provides automatic backlighting. In a dim room, the LIGHT SENSOR automatically turns on back- lighting for 6 seconds whenever a button is pressed.
In a dim room, you can manually turn on the lighting by pressing the LIGHT button on the side of the remote. The lights stay on for 6 seconds and for an additional 6 sec- onds each time another button is pressed.
NOTE: In a bright room, the backlighting function is dis- abled to save battery power.
Sliding Cover
A sliding cover conceals the buttons at the bottom of the RR-1050. These buttons provide extra command functions used in programming and configuring the unit. Leave the sliding cover in the UP position to simplify the RR-1050 for general use. Slide the cover DOWN to access the addi- tional buttons.
Device/Input Buttons ![](/images/new-backgrounds/1247407/2474079xi8.webp)
Nine buttons (AUD, CD, TUN, TAPE and V1 to V5) at the top of the RR-1050 are used to select the device or compo- nent you will control and to select the input source for the device you are operating. How long the button is pressed determines whether a device is selected or an input source is selected. For example, give the AUD button a short press
-less than one second - and the RR-1050 becomes the remote control for your Rotel audio/video receivers or sur- round sound processor. Then if you give the CD button a long press - more than one second - the CD input for the Surround Sound processor is selected and the CD player becomes the selected device.