Manuals / Runco / Computer Equipment / Projector

Runco CL-810 Overview, Rear / Bottom View, Connector Panel, Cable Opening, Cable Access Door

Models: CL-810

1 58

Page 11

Overview

1	2	3	Rear / Bottom View

1.Connector Panel

See “Connector Panel” on page 14.

2.AC Power IN Socket

3.AC Power Switch

4.Runco Logo

Can be rotated to match floor or ceiling installation.

See “Runco Logo” on page 14.

5.Cable Opening

Pass cables through this opening.

6.Cable Access Door

Open to access connectors.

See “Connector Panel” on page 14.

7.Lamp Module Cover

Remove this cover when replacing the lamp. See “Lamp Replacement” on page 45.

8.Front / Rear Adjusters Adjusts the height or projection angle.

9.Ceiling Mount Holes

The connecting holes for the ceiling mount bracket.

Runco CL-810 Owner’s Operating Manual

Page 11

Image 11

Contents

DLP Projector CL-810OW N E R ’S OP E R A T I N G MA N U A L Page Installation Table of ContentsLimited Warranty Safety PrecautionsRS-232 Setup Table of Contents continuedLamp Replacement TroubleshootingFor Projectors, Video Processors and Controllers WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTYWHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY TWO YEAR LIMITED WARRANTYRIGHTS, LIMITS AND EXCLUSIONS EFFECTIVE WARRANTY DATEIMPORTANT WARRANTY REGISTRATION CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE2900 Faber Street Union City, CA Ph 510 Fax 510 RUNCO INTERNATIONAL, INC Attn Customer Service DepartmentRUNCO VIDEO PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDSRunco CL-810 Owner’s Operating Manual Safety PrecautionsNative 169 Aspect Ratio, SuperOnyx TM DMD 1280 x 720p OverviewFeatures Reflectance Volume Regulation RVR2. Projection Lens 3. Top IR Sensor OverviewFront/Top View 1. Runco Logo8. Front / Rear Adjusters Adjusts the height or projection angle 1. Connector Panel2. AC Power IN Socket 3. AC Power Switch 4. Runco Logo 6. Cable Access DoorRunco CL-810 Owner’s Operating Manual OverviewThis page is intentionally left blank 1. LAMP LED Controls and Functions2. POWER LED Control Panel4. S-Video mini DIN 4-pin Y/C S-video signal input Connector PanelRunco Logo 3. Video RCA Jack Composite video signal inputRunco CL-810 Owner’s Operating Manual Remote ControlControls and Functions Runco CL-810 Owner’s Operating Manual Remote Control continuedControls and Functions Notes on Batteries InstallationRemote Control Notes on Remote Control OperationFront Screen, Inverted Mount ceiling Installation Installation ConsiderationsInstallation Front Screen, Floor Mount InstallationRunco CL-810 Owner’s Operating Manual InstallationRear screen installations Screen sizeRunco CL-810 Owner’s Operating Manual InstallationOther considerations and tips that can help improve your installation Adjusting the Projection Angle InstallationCeiling Installation Floor InstallationMounting Folded Optics InstallationRunco CL-810 Owner’s Operating Manual Runco CL-810 Owner’s Operating Manual Connecting Video InputsConnections DVD PlayerRGBHV DTV RGB ConnectionsRunco CL-810 Owner’s Operating Manual Progressive Component DTV Y/PB/PRConnections Connecting a ComputerConnecting an HDMI Device GBRHVRunco CL-810 Owner’s Operating Manual Connecting to AC PowerPower switch ConnectionsBasic Operation Turning on the PowerAdjusting the Zoom and Focus Adjusting the Vertical Lens Offset Adjusting Projector HeightBasic Operation Adjusting the PictureSelecting Video Memory Selecting an Aspect RatioBasic Operation Setting the MenuSelecting the Input Source PIP / PBP FunctionRunco CL-810 Owner’s Operating Manual Turning off the PowerBasic Operation Adjustment Using the MenuOn-Screen Display Menus Main MenuBrightness Contrast Color Tint Sharpness Picture Quality AdjustmentsOn-Screen Display Menus Runco CL-810 Owner’s Operating ManualICC Selection Store Image Settings Restore Image Settings NOTE You must enter a passcode in order to enter the Set Up menuColor Temperature Filter Color TemperatureLETTERBOX Aspect RatioOn-Screen Display Menus ANAMORPHICCINEMA Aspect Ratio continuedInstallation On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Keystone Adjust Background ColorKeystone Adjust On-Screen Display Menussource ONLY, press the arrow key to highlight “Yes” then OptionTo restore the default image settings for the current input On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Auto Adjusts the phase, frequency and position automaticallyOn-Screen Display Menus White Balance SetupOn-Screen Display Menus Runco CL-810 Owner’s Operating ManualRunco CL-810 Owner’s Operating Manual On-Screen Display MenusSelect from 1% to 10% of Over Scan, as desired Runco CL-810 Owner’s Operating Manual 7.5 IRE - Used for most NTSC video signalsOn-Screen Display Menus Runco CL-810 Owner’s Operating Manual Remote Control The Remote Control menu shows you the primary andOn-Screen Display Menus Fan Control Auto Normal Auto Hi. Altitude Manual Fan Speed +2 On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Fan Control ModeThis setting is described in the “Installation” section refer to page ISF CalibrationThese settings are described in the previous section, “Set Up.” These settings are described in the previous section, “Set Up.”Runco CL-810 Owner’s Operating Manual EnterRunco CL-810 Owner’s Operating Manual Return to User OSD To exit the ISF Calibration menu, use the up- or down-arrow keys to highlight Return to User OSD and press EnterRunco CL-810 Owner’s Operating Manual Lamp Replacementthe lamp assembly for replacement Runco CL-810 Owner’s Operating Manual Lamp ReplacementThis page is intentionally left blank red POWER LED TroubleshootingPROBLEM Remote controlRunco CL-810 Owner’s Operating Manual TroubleshootingThis page is intentionally left blank D-Sub 9-pin female RS-232 SetupConnecting RS-232 to the Projector RS-232 Pin AssignmentsAll codes are in the ASCII format RS-232 SetupA carriage return is required after each command RS-232C Control CodesCode RS-232C Control Codescontinued RS-232 SetupRunco CL-810 Owner’s Operating Manual RS-232 SetupThis page is intentionally left blank Throw Distance Factor x Screen Width Horizontal and Vertical Offset SpecificationsProjector Type Native Resolution Aspect Ratios Video Standards DTV Compatibility Scan Frequency Picture Size 169 screensRegulatory Approvals Limited Warranty SpecificationsBrightness and Contrast Power Requirements Operating Environment Dimensions Weight including lens8.86 in. 225.00 mm 2.17 in 55.00 mm 9.25 in DimensionsRunco CL-810 Owner’s Operating Manual 9.84 in. 250.00 mm 19.69 in. 500.00 mm 17.32 in. 440.00 mmSERIAL NUMBER RUMA-011135