Manuals / Runco / Computer Equipment / Projector

Runco manual Turning off the Power, Basic Operation, Runco CL-810 Owner’s Operating Manual

Models: CL-810

1 58

Page 30

Basic Operation

		• Press the OFF button to turn off the
	Turning off the Power	• Press the OFF button to turn off the
	Turning off the Power	projector.
		projector.
		• The POWER LED will blink green and the
		fans will speed up for a quick cool-down.
		The projector will not respond to any
		command for 90 seconds.

LIGHT

ONOFF

•The POWER LED will light solid orange once the cooling down cycle has completed.

•The fans will run for three minutes to cool.

•You can turn the projector back on after approximately two minutes.

VID S-VID COMP1 COMP2

RGBHD HDMI

30	Runco CL-810 Owner’s Operating Manual

Page 30

Image 30

Runco manual Turning off the Power, Basic Operation, Runco CL-810 Owner’s Operating Manual

Contents

CL-810 OW N E R ’S OP E R A T I N G MA N U A LDLP Projector Page Safety Precautions Table of ContentsLimited Warranty InstallationTroubleshooting Table of Contents continuedLamp Replacement RS-232 SetupTWO YEAR LIMITED WARRANTY WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTYWHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY For Projectors, Video Processors and ControllersCONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE EFFECTIVE WARRANTY DATEIMPORTANT WARRANTY REGISTRATION RIGHTS, LIMITS AND EXCLUSIONSRETAIN THIS INFORMATION FOR YOUR RECORDS RUNCO INTERNATIONAL, INC Attn Customer Service DepartmentRUNCO VIDEO PRODUCT INFORMATION 2900 Faber Street Union City, CA Ph 510 Fax 510Safety Precautions Runco CL-810 Owner’s Operating ManualReflectance Volume Regulation RVR OverviewFeatures Native 169 Aspect Ratio, SuperOnyx TM DMD 1280 x 720p1. Runco Logo OverviewFront/Top View 2. Projection Lens 3. Top IR Sensor6. Cable Access Door 1. Connector Panel2. AC Power IN Socket 3. AC Power Switch 4. Runco Logo 8. Front / Rear Adjusters Adjusts the height or projection angleOverview This page is intentionally left blankRunco CL-810 Owner’s Operating Manual Control Panel Controls and Functions2. POWER LED 1. LAMP LED3. Video RCA Jack Composite video signal input Connector PanelRunco Logo 4. S-Video mini DIN 4-pin Y/C S-video signal inputRemote Control Controls and FunctionsRunco CL-810 Owner’s Operating Manual Remote Control continued Controls and FunctionsRunco CL-810 Owner’s Operating Manual Notes on Remote Control Operation InstallationRemote Control Notes on BatteriesFront Screen, Floor Mount Installation Installation ConsiderationsInstallation Front Screen, Inverted Mount ceiling InstallationScreen size InstallationRear screen installations Runco CL-810 Owner’s Operating ManualInstallation Other considerations and tips that can help improve your installationRunco CL-810 Owner’s Operating Manual Floor Installation InstallationCeiling Installation Adjusting the Projection AngleInstallation Runco CL-810 Owner’s Operating ManualMounting Folded Optics DVD Player Connecting Video InputsConnections Runco CL-810 Owner’s Operating ManualProgressive Component DTV Y/PB/PR ConnectionsRunco CL-810 Owner’s Operating Manual RGBHV DTV RGBGBRHV Connecting a ComputerConnecting an HDMI Device ConnectionsConnections Connecting to AC PowerPower switch Runco CL-810 Owner’s Operating ManualAdjusting Projector Height Turning on the PowerAdjusting the Zoom and Focus Adjusting the Vertical Lens Offset Basic OperationSelecting an Aspect Ratio Adjusting the PictureSelecting Video Memory Basic OperationPIP / PBP Function Setting the MenuSelecting the Input Source Basic OperationTurning off the Power Basic OperationRunco CL-810 Owner’s Operating Manual Main Menu Using the MenuOn-Screen Display Menus AdjustmentRunco CL-810 Owner’s Operating Manual Picture Quality AdjustmentsOn-Screen Display Menus Brightness Contrast Color Tint SharpnessFilter Color Temperature NOTE You must enter a passcode in order to enter the Set Up menuColor Temperature ICC Selection Store Image Settings Restore Image SettingsANAMORPHIC Aspect RatioOn-Screen Display Menus LETTERBOXOn-Screen Display Menus Aspect Ratio continuedInstallation CINEMAOn-Screen Display Menus Keystone Adjust Background ColorKeystone Adjust Runco CL-810 Owner’s Operating ManualOn-Screen Display Menus OptionTo restore the default image settings for the current input source ONLY, press the arrow key to highlight “Yes” thenAuto Adjusts the phase, frequency and position automatically On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Runco CL-810 Owner’s Operating Manual SetupOn-Screen Display Menus White BalanceOn-Screen Display Menus Select from 1% to 10% of Over Scan, as desiredRunco CL-810 Owner’s Operating Manual 7.5 IRE - Used for most NTSC video signals On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Remote Control The Remote Control menu shows you the primary and On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Fan Control Mode On-Screen Display MenusRunco CL-810 Owner’s Operating Manual Fan Control Auto Normal Auto Hi. Altitude Manual Fan Speed +2These settings are described in the previous section, “Set Up.” ISF CalibrationThese settings are described in the previous section, “Set Up.” This setting is described in the “Installation” section refer to pageEnter Runco CL-810 Owner’s Operating ManualReturn to User OSD To exit the ISF Calibration menu, use the up- or down-arrow keys to highlight Return to User OSD and press Enter Runco CL-810 Owner’s Operating ManualLamp Replacement the lamp assembly for replacementRunco CL-810 Owner’s Operating Manual Lamp Replacement This page is intentionally left blankRunco CL-810 Owner’s Operating Manual Remote control TroubleshootingPROBLEM red POWER LEDTroubleshooting This page is intentionally left blankRunco CL-810 Owner’s Operating Manual RS-232 Pin Assignments RS-232 SetupConnecting RS-232 to the Projector D-Sub 9-pin femaleRS-232C Control Codes RS-232 SetupA carriage return is required after each command All codes are in the ASCII formatRS-232 Setup RS-232C Control Codescontinued CodeRS-232 Setup This page is intentionally left blankRunco CL-810 Owner’s Operating Manual DTV Compatibility Scan Frequency Picture Size 169 screens SpecificationsProjector Type Native Resolution Aspect Ratios Video Standards Throw Distance Factor x Screen Width Horizontal and Vertical OffsetDimensions Weight including lens SpecificationsBrightness and Contrast Power Requirements Operating Environment Regulatory Approvals Limited Warranty9.84 in. 250.00 mm 19.69 in. 500.00 mm 17.32 in. 440.00 mm DimensionsRunco CL-810 Owner’s Operating Manual 8.86 in. 225.00 mm 2.17 in 55.00 mm 9.25 inRUMA-011135 SERIAL NUMBER