Manuals / Runco / Home Audio / Home Theater System

Runco LS-10D operation manual Turning on the Power, Connecting to AC Power

Models: LS-10D

1 112

Download 112 pages 12.59 Kb

Page 55

Installation

Projector/DHD Controller: Plug the female end of one power cord into the AC receptacle on the rear of the LS-10d (AC 100V ~ 240V). Then, connect the other end to your AC power source.

Similarly connect the DHD Controller to a nearby AC outlet.

Anamorphic Lens Transport: An AC-to-DC power adapter is provided for the lens transport. Connect the power adapter to the +9V DC In jack on the rear of the lens transport assembly. Connect the other end to an AC power source.

1.Turn on your source components.

2.Turn on the main power switch at the rear of the DHD Controller.

3.Press the ON button on the remote control (or the ON/STANDBY ( ) button on DHD Controller front panel) to turn on the system. The vacuum fluorescent display on the DHD Controller front panel briefly displays “Initializing System,” followed by “Starting LS-10d.”

4.When the projector is ready for use, the fluorescent display indicates the active source, input resolution/frame rate and aspect ratio; for example:

				Current
				Source
LS-10d
LS-10d			HDMI 1
16:9			1080i/60

Connecting to AC Power

3.7

Turning on the Power

Aspect Ratio

Input Resolution/Frame Rate

Runco LS-10d Installation/Operation Manual

39

Image 55

Runco LS-10D operation manual Turning on the Power, Connecting to AC Power

Contents

and Digital High Definition DHD Controller/Scaler/Processor LS-10dI N S T A L L A T I O N / O P E R A T I O N M A N U A L DLPTM Home Theater ProjectorPage Length of Warranty RuncoCare Standard Two Year Limited WarrantyRuncoCare Standard Features Warranty CoverageWarranty Exclusions RuncoCare Claim ProcedureSub Pixel Policy Extended Service OptionsOther Terms and Conditions Effect of Local Law Online Product RegistrationLimitation of Implied Warranties Exclusion of DamagesImportant Safety Instructions DECLARATION OF CONFORMITY Compliance InformationIMPORTANT RECYCLE INSTRUCTIONS FCC PARTINDUSTRY CANADA ICES-003 PRODUCT DISPOSALPage Runco LS-10d Installation/Operation Manual Table of ContentsRuncoCare Standard Two Year Limited Warranty viiiInstalling the Optional Anamorphic Lens Mount External Control Maintenance and TroubleshootingSpecifications Runco LS-10d Installation/Operation ManualRunco LS-10d Installation/Operation Manual Table of ContentsList of Figures Runco LS-10d Installation/Operation ManualList of Figures Runco LS-10d Installation/Operation ManualTarget Audience A carriage return must be used after each command or string1. Introduction 1.1 About This ManualDANGER 1.2 Using This Manualcertain features DANGER appears when a given action can cause severe injury orformat screen 1.3 Description, Features and BenefitsOptional Accessories SYSTEM KEYPAD 2. Controls and Functions2.1 LS-10d at a Glance Figure 2-1. LS-10d Front/Side View STATUS LEDRunco Logo Badge Rear Cover Lamp Module Cover Cable Opening PROJECTION LENSFigure 2-2. LS-10d Rear/Bottom/Top View Ceiling Mount Holes Adjustable FeetCABLE OPENING ADJUSTABLE FEETRUNCO LOGO BADGE REAR COVER LAMP MODULE COVER2. TRIGGER 3. POWER INPUT 100 to 240 VAC Connect the LS-10d to power here2.2 LS-10d Rear Panel Figure 2-3. LS-10d Rear Panel 1. DHD INPUT3. VACUUM FLUORESCENT DISPLAY 2.3 DHD Controller Front PanelFigure 2-4. DHD Controller Front Panel 1. RUNCO ICON 2. IR SENSOR8. MENU BUTTON Figure 2-5. DHD Controller Rear Panel 1. MAIN POWER SWITCH2.4 DHD Controller Rear Panel 7. RIGHT BUTTON6. IR 4. RS-232 To Accessory Box9. Component / SCART 3 x RCA connectors 5. Display ControlControls and Functions 2.5 LS-10d Remote Control UnitFigure 2-6. DHD Controller/LS-10d Remote Control Runco LS-10d Installation/Operation Manual3. ON / OFF 1. IR OUTPUT INDICATOR8. Memory Preset Buttons ISF NIGHT 2. LIGHT13. SCART 10. HD 1 4 / HD 211. COMP Component 12. HDMI 1 7 / HDMI 2 8 / HDMI 3 / HDMI 4Notes on Batteries Notes on Remote Control Operation 3. Installation3.1 Remote Control installation specialistProcedure 3.2 Quick SetupTable 3-1. Installation Overview InstallationTable 3-2. Projector Installation Options 3.3 Installation ConsiderationsInstallation Type Figure 3-1. Estimating Throw Distance Ambient LightThrow Distance Estimating Throw DistanceThrow Range in Table 3-3. LS-10d Lens Options and Throw Ratios NoteInstallation Runco LS-10d Installation/Operation ManualVertical and Horizontal Ceiling InstallationFloor Installation Figure 3-2. Projector PlacementScreen Center 0% Figure 3-4. Horizontal Lens Shift EXAMPLE ONLYAudio/Video Synchronization IssuesTable 3-4. Possible Audio Latency for Various Input Timings Figure 3-5. Folded Opticsinstall the projector and adjust the primary lens 3.4 Installing the Optional Anamorphic Lens Mount1. Do not install the anamorphic lens yet, only the lens mount and transport assembly. You will install the anamorphic lens after youRunco LS-10d Installation/Operation Manual Attaching the Transport Assembly Attachment PlateInstallation for Transport Assembly Attachment Plate and Ceiling Mount PlateAttachment Points for Security Hooks Assembly Attachment plate 2. DO NOT OVER-TIGHTEN THE SCREWSInstallation Runco LS-10d Installation/Operation ManualAnamorphic Lens Transport Assembly Pliers Scissors Ceiling Hooks not supplied Use only the Runco-approved ceiling mount kit designed for your Installing the Projector in3.5 Mounting the LS-10d Floor Mounting Upright Ceiling Mounting InvertedAngle Adjusting the ProjectionFigure 3-6. Mounting Angle Ranges Front-to-Back and Side-to-Side Controller Connector Panel AccessConnections to the LS-10d and DHDUse an HDMI cable for this connection. A DVI cable with Connecting the DHDFigure 3-7. Connecting the LS-10d to the DHD Controller Controller to the LS-10dHDMI Source Connections See Figure Connecting SourceComponents to the DHD ControllerDTV-Set-Top Box Figure 3-9. Component Video Source ConnectionsInstallation Runco LS-10d Installation/Operation ManualComputer Figure 3-10. RGBHV Source ConnectionsInstallation Runco LS-10d Installation/Operation ManualDVD/DTV STB Figure 3-11. SCART RGBS Source ConnectionsGaming Console Connection Composite Source Connections See FigureFigure 3-12. Composite Video Source Connections RS-232 Controller3.5-mm mini plug Connecting 12-volt Trigger Outputs to External EquipmentFigure 3-14. 12-volt Trigger Output Connection from DHD Controller You can also use a 12-volt trigger output on the DHD Controller toRemote Control Connecting an External IRReceiver to the DHD Figure 3-16. External IR Receiver ConnectionConnecting to AC Power 3.7 Turning on the PowerFocus Zoom Vertical and Horizontal Lens Shift 3.8 Primary Lens Adjustments3.9 Adjusting the Picture Orientation You must enter a passcode to access the Service menuHorizontal Keystoning Vertical Keystoning Pincushion Distortion 3.10 Adjusting the Image GeometryFigure 3-17. Keystone and Pincushion Distortion The “Left Middle y” setting also controls the “Right Middle” You must enter a passcode to access the Calibration menuFigure 3-18. Image Alignment Controls It is extremely important that the primary lens is properly 3.11 Installing and Adjusting the Anamorphic LensInstallation and Adjustmenttime after turning on the system Adjusting the Lens PositionThere may be some pincushion distortion even after the lens is 4. Operation 4.1 Using the On-Screen MenusPresets Sleep TimerOperation ServiceFigure 4-1. DHD Controller OSD Menu Structure for LS-10d continued Runco LS-10d Installation/Operation ManualThe aspect ratio selection is automatically saved for each input and Note resolutionMain Menu Input SourceAspect Ratio Table 4-1. Aspect Ratio SettingsOperation RemoteRemote Table 4-1. Aspect Ratio Settings continuedRunco LS-10d Installation/Operation Manual OperationFigure 4-2. Typical PLUGE Pattern for Adjusting Brightness 1. When you change a picture quality setting, save the change to aPicture Brightness and contrast controls are interactive. A change to one Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrastgreen grayyellow cyangreen grayyellow cyanand resolution Figure 4-5. Typical Test Pattern for Adjusting SharpnessInput Position Figure 4-6. Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsSleep Timer To save the settings for the current input and display mode to theYou must enter a passcode to access the Calibration menu InformationCalibration should be used by ISF-certified technicians onlyMagenta Figure 4-7. CIE 1931 Chromaticity DiagramYellow Cy a nmodes on a given input Table 4-2. Color Temperature Presets and Associated Color Pointsa given input Table 4-3. x/y Color Gamut ValuesSaturation The Input Image settings establish the “zero point” for the PictureFigure 4-8. Effect of PCE Hue and Saturation Controls Copy/Paste Copied settings are not retained after a power cycleYou must enter a passcode to access the Service menu Serviceshould be used by ISF-certified technicians only To restore the normal picture all colors, select White To manually configure these values, set DHCP to Off enabledThe notification messages are in the following format 2. Highlight Enable and press ENTER 3. Highlight On and press ENTER The default setting, Auto, functions as follows Firmware Upgrade functionsDHD Controller remote control to send that same code. To do this remote to match as described below1. Setting CEC to Off prevents communication between the DHD Logo LED page 56 and ISF Day/Night Memory Presets pageStandby LED 5.1 Lamp Replacement 5. Maintenance and TroubleshootingSymptom 5.2 Troubleshooting TipsTable 5-1. Troubleshooting Chart Maintenance and Troubleshooting6. External Control Port ConfigurationSerial Command Syntax Avoid combining the ON or POWER 1 commands with other commandsExternal Control Table 6-1. Serial CommandsPicture Adjust Commands Table 6-1. Serial Commands continuedCommand Aspect Ratio CommandsInput Position Commands Table 6-1. Serial Commands continuedCommand Image Preset CommandsMiscellaneous Commands Table 6-1. Serial Commands continuedCommand Sleep Timer CommandsTable 6-1. Serial Commands continued 6.2 Using Discrete IR CodesTable 6-2. RC5 Control Codes for the DHD Controller IR Command ListFigure 6-1. RC5 Message Format RC5 Data Table 6-2. RC5 Control Codes for the DHD Controller continuedRemote Control External ControlExternal Control Remote ControlRunco LS-10d Installation/Operation Manual Table 6-2. RC5 Control Codes for the DHD Controller continuedTable 6-3. CEC Commands Supported by the DHD Controller 6.3 Using HDMI CEC MessagesExternal Control Table 6-3. CEC Commands Supported by the DHD Controller continuedmessages from the “HDMI Audio Out” connector Runco LS-10d Installation/Operation ManualExternal Control Runco LS-10d Installation/Operation ManualNative Resolution 7. SpecificationsLS-10d Specifications Table 7-1. LS-10d SpecificationsHome Theater Calibration Specifications Table 7-1. LS-10d Specifications continuedSpecifications SpecificationsPower Requirements 7.2 DHD Controller SpecificationsTable 7-2. DHD Controller Specifications SpecificationsRunco LS-10d Installation/Operation Manual 7.3 LS-10d DimensionsFigure 7-1. LS-10d Dimensions SpecificationsResolution Table 7-3. Supported Signal Timings by InputSupported Timings SpecificationsSupported? √ = Yes, - = No Table 7-3. Supported Signal Timings by Input continuedSpecifications ResolutionRunco LS-10d Installation/Operation Manual Table 7-3. Supported Signal Timings by Input continuedSpecifications ResolutionSpecifications Page 020-1073-00 Rev. A September