Manuals / Runco / Home Audio / Home Theater System

Runco LS-10D operation manual page 56 and ISF Day/Night Memory Presets page, Logo LED, Standby LED

Models: LS-10D

1 112

Download 112 pages 12.59 Kb

Page 88

Operation

Front Panel Brightness: Select Front Panel Brightness from the Service menu to adjust the brightness of the front-panel LED and LCD status indicators.

Logo LED

LCD

Standby LED

•Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the brightness of the large, illuminated logo on the left side of the display. The range is from 0 (off) to 31.

•Standby LED: Select Standby LED from the Front Panel Brightness menu to change the behavior of the front-panel STANDBY indicator LED. When set to ON, the LED lights amber when the system is in standby mode; otherwise, it is off. When set to OFF, the LED is always off.

•LCD: Select LCD from the Front Panel Brightness menu to adjust the brightness of the front-panel LCD. The range is from 0 (off) to 4.

Auto Power Off: Select Auto Power Off from the Service menu to have the LS-10d turn itself off after a period of inactivity (no source signal present).

•Enable: By default, Auto Power Off is disabled. To enable it, select Enable from the Auto Power Off sub-menu and set it to On.

•Hours: The default time-out period is eight (8) hours; the range is from 1 to 24 hours.

System Reset: To reset ALL controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears. Select Yes to continue with the reset or select No to cancel.

This action is not undoable. Proceed with caution! Before you Caution perform a System Reset, save your “Custom” Memory Presets

(page 56) and ISF Day/Night Memory Presets (page 63).

72	Runco LS-10d Installation/Operation Manual

Image 88

Contents

LS-10d I N S T A L L A T I O N / O P E R A T I O N M A N U A LDLPTM Home Theater Projector and Digital High Definition DHD Controller/Scaler/ProcessorPage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesWarranty Coverage Length of WarrantyRuncoCare Claim Procedure Warranty ExclusionsSub Pixel Policy Extended Service OptionsOther Terms and Conditions Online Product Registration Limitation of Implied WarrantiesExclusion of Damages Effect of Local LawImportant Safety Instructions Compliance Information DECLARATION OF CONFORMITYFCC PART INDUSTRY CANADA ICES-003PRODUCT DISPOSAL IMPORTANT RECYCLE INSTRUCTIONSPage Table of Contents RuncoCare Standard Two Year Limited Warrantyviii Runco LS-10d Installation/Operation ManualInstalling the Optional Anamorphic Lens Mount Maintenance and Troubleshooting SpecificationsRunco LS-10d Installation/Operation Manual External ControlTable of Contents Runco LS-10d Installation/Operation ManualRunco LS-10d Installation/Operation Manual List of FiguresRunco LS-10d Installation/Operation Manual List of FiguresA carriage return must be used after each command or string 1. Introduction1.1 About This Manual Target Audience1.2 Using This Manual certain featuresDANGER appears when a given action can cause severe injury or DANGER1.3 Description, Features and Benefits format screenOptional Accessories 2. Controls and Functions 2.1 LS-10d at a GlanceFigure 2-1. LS-10d Front/Side View STATUS LED SYSTEM KEYPADPROJECTION LENS Figure 2-2. LS-10d Rear/Bottom/Top ViewCeiling Mount Holes Adjustable Feet Runco Logo Badge Rear Cover Lamp Module Cover Cable OpeningADJUSTABLE FEET RUNCO LOGO BADGE REAR COVERLAMP MODULE COVER CABLE OPENING3. POWER INPUT 100 to 240 VAC Connect the LS-10d to power here 2.2 LS-10d Rear PanelFigure 2-3. LS-10d Rear Panel 1. DHD INPUT 2. TRIGGER2.3 DHD Controller Front Panel Figure 2-4. DHD Controller Front Panel 1. RUNCO ICON2. IR SENSOR 3. VACUUM FLUORESCENT DISPLAYFigure 2-5. DHD Controller Rear Panel 1. MAIN POWER SWITCH 2.4 DHD Controller Rear Panel7. RIGHT BUTTON 8. MENU BUTTON4. RS-232 To Accessory Box 9. Component / SCART 3 x RCA connectors5. Display Control 6. IR2.5 LS-10d Remote Control Unit Figure 2-6. DHD Controller/LS-10d Remote ControlRunco LS-10d Installation/Operation Manual Controls and Functions1. IR OUTPUT INDICATOR 8. Memory Preset Buttons ISF NIGHT2. LIGHT 3. ON / OFF10. HD 1 4 / HD 2 11. COMP Component12. HDMI 1 7 / HDMI 2 8 / HDMI 3 / HDMI 4 13. SCART3. Installation 3.1 Remote Controlinstallation specialist Notes on Batteries Notes on Remote Control Operation3.2 Quick Setup Table 3-1. Installation OverviewInstallation ProcedureTable 3-2. Projector Installation Options 3.3 Installation ConsiderationsInstallation Type Ambient Light Throw DistanceEstimating Throw Distance Figure 3-1. Estimating Throw DistanceTable 3-3. LS-10d Lens Options and Throw Ratios Note InstallationRunco LS-10d Installation/Operation Manual Throw Range inCeiling Installation Floor InstallationFigure 3-2. Projector Placement Vertical and HorizontalFigure 3-4. Horizontal Lens Shift EXAMPLE ONLY Screen Center 0%Synchronization Issues Table 3-4. Possible Audio Latency for Various Input TimingsFigure 3-5. Folded Optics Audio/Video3.4 Installing the Optional Anamorphic Lens Mount 1. Do not install the anamorphic lens yet, only the lens mount andtransport assembly. You will install the anamorphic lens after you install the projector and adjust the primary lensAttaching the Transport Assembly Attachment Plate Installationfor Transport Assembly Attachment Plate and Ceiling Mount Plate Runco LS-10d Installation/Operation ManualAssembly Attachment plate 2. DO NOT OVER-TIGHTEN THE SCREWS InstallationRunco LS-10d Installation/Operation Manual Attachment Points for Security HooksAnamorphic Lens Transport Assembly Pliers Scissors Ceiling Hooks not supplied Installing the Projector in 3.5 Mounting the LS-10dFloor Mounting Upright Ceiling Mounting Inverted Use only the Runco-approved ceiling mount kit designed for yourAngle Adjusting the ProjectionFigure 3-6. Mounting Angle Ranges Front-to-Back and Side-to-Side Connector Panel Access Connections to theLS-10d and DHD ControllerConnecting the DHD Figure 3-7. Connecting the LS-10d to the DHD ControllerController to the LS-10d Use an HDMI cable for this connection. A DVI cable withConnecting Source Components to the DHDController HDMI Source Connections See FigureFigure 3-9. Component Video Source Connections InstallationRunco LS-10d Installation/Operation Manual DTV-Set-Top BoxFigure 3-10. RGBHV Source Connections InstallationRunco LS-10d Installation/Operation Manual ComputerDVD/DTV STB Figure 3-11. SCART RGBS Source ConnectionsGaming Console Composite Source Connections See Figure Figure 3-12. Composite Video Source ConnectionsRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment Figure 3-14. 12-volt Trigger Output Connection from DHD ControllerYou can also use a 12-volt trigger output on the DHD Controller to 3.5-mm mini plugConnecting an External IR Receiver to the DHDFigure 3-16. External IR Receiver Connection Remote Control3.7 Turning on the Power Connecting to AC Power3.8 Primary Lens Adjustments 3.9 Adjusting the Picture OrientationYou must enter a passcode to access the Service menu Focus Zoom Vertical and Horizontal Lens ShiftHorizontal Keystoning Vertical Keystoning Pincushion Distortion 3.10 Adjusting the Image GeometryFigure 3-17. Keystone and Pincushion Distortion The “Left Middle y” setting also controls the “Right Middle” You must enter a passcode to access the Calibration menuFigure 3-18. Image Alignment Controls 3.11 Installing and Adjusting the Anamorphic Lens Installation andAdjustment It is extremely important that the primary lens is properlytime after turning on the system Adjusting the Lens PositionThere may be some pincushion distortion even after the lens is 4.1 Using the On-Screen Menus PresetsSleep Timer 4. OperationService Figure 4-1. DHD Controller OSD Menu Structure for LS-10d continuedRunco LS-10d Installation/Operation Manual OperationNote resolution Main MenuInput Source The aspect ratio selection is automatically saved for each input andTable 4-1. Aspect Ratio Settings OperationRemote Aspect RatioTable 4-1. Aspect Ratio Settings continued Runco LS-10d Installation/Operation ManualOperation RemoteFigure 4-2. Typical PLUGE Pattern for Adjusting Brightness 1. When you change a picture quality setting, save the change to aPicture Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast Brightness and contrast controls are interactive. A change to onegray yellowcyan greengray yellowcyan greenand resolution Figure 4-5. Typical Test Pattern for Adjusting SharpnessInput Position Figure 4-6. Overscan Modes Memory Presets Adjust the Phase after adjusting Tracking see belowTo save the settings for the current input and display mode to the Sleep TimerInformation Calibrationshould be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuFigure 4-7. CIE 1931 Chromaticity Diagram YellowCy a n MagentaTable 4-2. Color Temperature Presets and Associated Color Points modes on a given inputTable 4-3. x/y Color Gamut Values a given inputSaturation The Input Image settings establish the “zero point” for the PictureFigure 4-8. Effect of PCE Hue and Saturation Controls Copied settings are not retained after a power cycle Copy/PasteYou must enter a passcode to access the Service menu Serviceshould be used by ISF-certified technicians only To restore the normal picture all colors, select White enabled To manually configure these values, set DHCP to OffThe notification messages are in the following format 2. Highlight Enable and press ENTER 3. Highlight On and press ENTER Firmware Upgrade functions The default setting, Auto, functions as followsremote to match as described below DHD Controller remote control to send that same code. To do this1. Setting CEC to Off prevents communication between the DHD Logo LED page 56 and ISF Day/Night Memory Presets pageStandby LED 5. Maintenance and Troubleshooting 5.1 Lamp Replacement5.2 Troubleshooting Tips Table 5-1. Troubleshooting ChartMaintenance and Troubleshooting SymptomPort Configuration Serial Command SyntaxAvoid combining the ON or POWER 1 commands with other commands 6. External ControlTable 6-1. Serial Commands External ControlTable 6-1. Serial Commands continued CommandAspect Ratio Commands Picture Adjust CommandsTable 6-1. Serial Commands continued CommandImage Preset Commands Input Position CommandsTable 6-1. Serial Commands continued CommandSleep Timer Commands Miscellaneous Commands6.2 Using Discrete IR Codes Table 6-1. Serial Commands continuedTable 6-2. RC5 Control Codes for the DHD Controller IR Command ListFigure 6-1. RC5 Message Format Table 6-2. RC5 Control Codes for the DHD Controller continued Remote ControlExternal Control RC5 DataRemote Control Runco LS-10d Installation/Operation ManualTable 6-2. RC5 Control Codes for the DHD Controller continued External Control6.3 Using HDMI CEC Messages Table 6-3. CEC Commands Supported by the DHD ControllerTable 6-3. CEC Commands Supported by the DHD Controller continued messages from the “HDMI Audio Out” connectorRunco LS-10d Installation/Operation Manual External ControlRunco LS-10d Installation/Operation Manual External Control7. Specifications LS-10d SpecificationsTable 7-1. LS-10d Specifications Native ResolutionTable 7-1. LS-10d Specifications continued SpecificationsSpecifications Home Theater Calibration Specifications7.2 DHD Controller Specifications Table 7-2. DHD Controller SpecificationsSpecifications Power Requirements7.3 LS-10d Dimensions Figure 7-1. LS-10d DimensionsSpecifications Runco LS-10d Installation/Operation ManualTable 7-3. Supported Signal Timings by Input Supported TimingsSpecifications ResolutionTable 7-3. Supported Signal Timings by Input continued SpecificationsResolution Supported? √ = Yes, - = NoTable 7-3. Supported Signal Timings by Input continued SpecificationsResolution Runco LS-10d Installation/Operation ManualSpecifications Page 020-1073-00 Rev. A September