And ISF Day/Night Memory Presets | Runco Q-750D instruction

Operation

Front Panel Brightness: Select Front Panel Brightness from the Service menu to adjust the brightness of the front-panel LED and LCD status indicators.

Logo LED

LCD

Standby LED

•Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the brightness of the large, illuminated logo on the left side of the display. The range is from 0 (off) to 31.

•Standby LED: Select Standby LED from the Front Panel Brightness menu to change the behavior of the front-panel STANDBY indicator LED. When set to ON, the LED lights amber when the system is in standby mode; otherwise, it is off. When set to OFF, the LED is always off.

•LCD: Select LCD from the Front Panel Brightness menu to adjust the brightness of the front-panel LCD. The range is from 0 (off) to 4.

Auto Power Off: Select Auto Power Off from the Service menu to have the Q-750d turn itself off after a period of inactivity (no source signal present).

•Enable: By default, Auto Power Off is disabled. To enable it, select Enable from the Auto Power Off sub-menu and set it to On.

•Hours: The default time-out period is eight (8) hours; the range is from 1 to 24 hours.

System Reset: To reset ALL controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears. Select Yes to continue with the reset or select No to cancel.

This action is not undoable. Proceed with caution! Before you Caution perform a System Reset, save your “Custom” Memory Presets

(page 58) and ISF Day/Night Memory Presets (page 65).

70	Q-750d Series Installation/Operation Manual

Image 86

Runco Q-750D operation manual and ISF Day/Night Memory Presets

Contents

750d Series 750d 750d/CineWide 750d/CineWide with AutoScopePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Maintenance and Troubleshooting Operation Specifications External Control Table of Contents Xiv List of Figures List of Figures Introduction About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunction Description, Features and Benefits Format screen Optional Accessories Controls and Functions 750d at a Glance Off = Normal operation Power Input 100 to 240 VAC Connect the Q-750d to power here750d Rear Panel DHD Controller Front Panel Virtual Cinema is available only on the Q-750d/CineWide or DHD Controller Rear Panel DHD Controller Rear Panel Outputs Inputs 750d Remote Control Unit DHD Controller/Q-750d Remote Control Information about aspect ratios, refer to Table On / OFFCursor Buttons Menu button see below to exit the current menu 169 Memory Preset ButtonsAspect Ratio Selection Buttons Letbox Letterbox Installation specialist InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Ambient Light Throw Distance Lens Screen Lens Only Anamorphic Minimum Maximum Throw Ratios for the Q-750d SeriesPrimary Vertical and Horizontal Ceiling InstallationFloor Installation Position Vertical lens shift figures are for ceiling mount Audio/Video Synchronization IssuesPossible Audio Latency for Various Input Timings Input Timing Possible Audio Latency milliseconds Installing the Optional CineWide/AutoScope Lens Mount Other Considerations Q-750d/CineWide with AutoScope Motor Assembly Exploded View Lens Motor Q-750d/CineWide with AutoScope Remove Projector Front Feet Install Lens Motor Q-750d with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate 750d/CineWide Do not use the mounting screws provided with the ceiling Lens base plate Floor Mounting Upright Ceiling Mounting Inverted Adjusting the ProjectionMounting the Q-750d Angle Connections to the Q-750d and DHD Controller Connector Panel AccessConnecting the DHD Controller to the Q-750d 11. RS-232 Connection from the DHD Controller to the Q-750d Hdmi Source Connections See Figure Connecting SourceComponents to the DHD Controller 13. Component Video Source Connections DTV-Set-Top Box Computer RGB Camcorder Gaming Console 15. Scart Rgbs Source Connections Composite and S-Video Source Connections Camcorder RS-232 Controller Connection Connecting 12-volt Trigger Outputs to External Equipment AutoScope Lens Motor Connecting an External IR Receiver to the DHD Turning on the Power Connecting to AC Power You must enter a passcode to access the Service menu Primary Lens AdjustmentsAdjusting the Picture Orientation Zoom Out Focus It is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment 21. Attaching the Anamorphic Lens to the Lens Ring Adjusting the Horizontal X Lens Position Time after turning on the system Installation Anamorphic Lens Top View Geometry Using the On-Screen Menus Operation Runco Video ServiceMain Menu Input Source Input SourceAspect Ratio Aspect Ratio Select 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Hdtv programs in their Remote Aspect Ratio Control Description Key Overscan Picture Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Memory Presets Memory PresetsAdjust the Phase after adjusting Tracking see below Sleep Timer Sleep Timer Calibration You must enter a passcode to access the Calibration menuInformation Should be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Modes on a given input Color Temperature Presets and Associated Color PointsColor Temperature Preset Associated x/y Values Color X/y Color Gamut ValuesGiven input Hue SaturationHue Saturation Copied settings are not retained after a power cycle Copy/Paste Service Service Input Names Operation Operation 58 and ISF Day/Night Memory Presets Troubleshooting Chart Maintenance and TroubleshootingTroubleshooting Tips Symptom Possible Causes Solution Maintenance and Troubleshooting External Control Port ConfigurationSerial Command Syntax Serial Communications Serial Commands Input Selection Commands Picture Adjust Commands Input Position Commands Output Shift Commands Exit Return key Miscellaneous CommandsEnter key With Toggle Bit = Hex Binary Function Start Using Discrete IR CodesCommand Bits RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Data Enter Q-750d Specifications Specifications750d Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications Dimensions DHD Controller Specifications DHD Controller Specifications Overall Dimensions Q-750d Overall Dimensions Q-750d Overall Dimensions Q-750d/CineWide with AutoScope Overall Dimensions Q-750d/CineWide with AutoScope Supported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = No Video Video 1 S-Video Format Resolution FrequencyComponent/ Rgbhv Rate Hz MHz KHz PAL-M Page 020-0997-00 Rev. a November