Turning on the Power, Connecting to AC Power | Runco Q-750D manual

Installation

Projector/DHD Controller: Plug the female end of one power cord into the AC receptacle on the rear of the Q-750d (AC 100V ~ 240V). Then, connect the other end to your AC power source.

Similarly connect the DHD Controller to a nearby AC outlet.

AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power cord is provided for the lens motor. Plug the female end of the AC power cord into the AC input on the rear of the lens motor assembly. Connect the other end to your AC power source.

1.Turn on your source components.

2.Turn on the main power switch at the rear of the DHD Controller.

3.If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input.

4.Press the ON button on the remote control (or the ON/STANDBY ( ) button on DHD Controller front panel) to turn on the system. The vacuum fluorescent display on the DHD Controller front panel briefly displays “Initializing System,” followed by “Starting Q-750d.” On the projector, the LED flashes green to indicate that it is warming up.

5.When the projector is ready for use, the LED turns off. On the DHD Controller, the fluorescent display indicates the active source, input resolution/frame rate and aspect ratio; for example:

Current

Source

Connecting to AC Power

3.7

Turning on the Power

Q-750d

HDMI 1

16:91080i/60

Aspect Ratio

Input Resolution/Frame Rate

Q-750d Series Installation/Operation Manual

39

Image 55

Runco Q-750D operation manual Turning on the Power, Connecting to AC Power

Contents

750d 750d/CineWide 750d/CineWide with AutoScope 750d SeriesPage RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and Troubleshooting External Control Specifications Table of Contents Xiv List of Figures List of Figures About This Manual Introduction Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental information Format screen Description, Features and Benefits Optional Accessories 750d at a Glance Controls and Functions 750d Rear Panel Power Input 100 to 240 VAC Connect the Q-750d to power hereOff = Normal operation Virtual Cinema is available only on the Q-750d/CineWide or DHD Controller Front Panel DHD Controller Rear Panel DHD Controller Rear Panel Inputs Outputs DHD Controller/Q-750d Remote Control 750d Remote Control Unit Menu button see below to exit the current menu On / OFFCursor Buttons Information about aspect ratios, refer to Table Letbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 169 Remote Control InstallationInstallation specialist Installation Overview Quick SetupStep Procedure For Details, Refer to Projector Installation Options Installation ConsiderationsInstallation Type Throw Distance Ambient Light Primary Throw Ratios for the Q-750d SeriesLens Screen Lens Only Anamorphic Minimum Maximum Position Ceiling InstallationFloor Installation Vertical and Horizontal Vertical lens shift figures are for ceiling mount Input Timing Possible Audio Latency milliseconds Synchronization IssuesPossible Audio Latency for Various Input Timings Audio/Video Other Considerations Installing the Optional CineWide/AutoScope Lens Mount Lens Motor Q-750d/CineWide with AutoScope Q-750d/CineWide with AutoScope Motor Assembly Exploded View Remove Projector Front Feet Q-750d with Ceiling Mount Adapters/Projector Stands Install Lens Motor AutoScope Lens Motor Installation CineWide Base Plate 750d/CineWide Installing the Fixed Lens base plate Do not use the mounting screws provided with the ceiling Angle Adjusting the ProjectionMounting the Q-750d Floor Mounting Upright Ceiling Mounting Inverted Connecting the DHD Controller to the Q-750d Connector Panel AccessConnections to the Q-750d and DHD Controller 11. RS-232 Connection from the DHD Controller to the Q-750d Controller Connecting SourceComponents to the DHD Hdmi Source Connections See Figure DTV-Set-Top Box 13. Component Video Source Connections RGB Camcorder Computer 15. Scart Rgbs Source Connections Gaming Console Camcorder Composite and S-Video Source Connections Connection RS-232 Controller AutoScope Lens Motor Connecting 12-volt Trigger Outputs to External Equipment Receiver to the DHD Connecting an External IR Connecting to AC Power Turning on the Power Zoom Out Focus Primary Lens AdjustmentsAdjusting the Picture Orientation You must enter a passcode to access the Service menu Anamorphic Lens Installation Adjustment Installing and Adjusting the CineWide Anamorphic LensIt is extremely important that the primary lens is properly 21. Attaching the Anamorphic Lens to the Lens Ring Time after turning on the system Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Geometry Operation Using the On-Screen Menus Main Menu ServiceRunco Video Aspect Ratio Input SourceAspect Ratio Input Source Hdtv programs in their Aspect Ratio SettingsRemote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDs Overscan Remote Aspect Ratio Control Description Key Picture Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Overscan Modes Adjust the Phase after adjusting Tracking see below Memory PresetsMemory Presets Sleep Timer Sleep Timer Should be used by ISF-certified technicians only You must enter a passcode to access the Calibration menuInformation Calibration CIE 1931 Chromaticity Diagram Color Temperature Preset Associated x/y Values Color Temperature Presets and Associated Color PointsModes on a given input Given input X/y Color Gamut ValuesColor Hue Saturation SaturationHue Copy/Paste Copied settings are not retained after a power cycle Service Service Input Names Operation Operation 58 and ISF Day/Night Memory Presets Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting Chart Maintenance and Troubleshooting Serial Communications Port ConfigurationSerial Command Syntax External Control Input Selection Commands Serial Commands Picture Adjust Commands Output Shift Commands Input Position Commands Enter key Miscellaneous CommandsExit Return key Command Bits Using Discrete IR CodesWith Toggle Bit = Hex Binary Function Start RC5 Data IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 Control Codes for the DHD Controller Enter 750d Specifications SpecificationsQ-750d Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power Requirements DHD Controller Specifications DHD Controller Specifications Overall Dimensions Q-750d Overall Dimensions Q-750d Overall Dimensions Q-750d/CineWide with AutoScope Overall Dimensions Q-750d/CineWide with AutoScope Supported? √ = Yes, = No Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported Timings Rate Hz MHz KHz Video 1 S-Video Format Resolution FrequencyComponent/ Rgbhv Video PAL-M Page 020-0997-00 Rev. a November