Manuals / Runco / TV and Video / Flat Panel Television

Runco XP-OPAL50 Quick Setup, Installation must be performed by a qualified custom video

Models: XP-OPAL65 XP-OPAL50

1 86

Download 86 pages 59.65 Kb

Page 26

Installation

3.2

Quick Setup

Table 3-1gives a quick overview of the CinemaWall installation process. The sections following this one provide detailed instructions.

	Note		Installation must be performed by a qualified custom video
	Note		installation specialist.
Table 3-1. Installation Overview

Step			Procedure	For Details, refer to
Step			Procedure	page...
				page...

1		Mount the CinemaWall on a wall or table stand		13

2		Connect signal sources to the CinemaWall		16

3		Connect external controller to CinemaWall SERIAL port		19
		(optional)

4		Apply power to the CinemaWall		21

5		If using the CinemaWall with a computer, adjust computer		22
		display properties

6		Display calibration: adjust the following for each input:		23
		• Aspect ratio
		• Picture Level
		• Brightness
		• Color level
		• Tint
		• Sharpness
		• White Balance

12	CinemaWall Installation/Operation Manual

Image 26

Runco XP-OPAL50 Quick Setup, Installation must be performed by a qualified custom video, Installation specialist

Contents

XP-50 XP-65Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Appendix A. Default Settings Maintenance and TroubleshootingSpecifications OperationList of Figures List of Figures Xiv About This Manual Carriage return must be used after each command or stringIntroduction Target AudienceSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories XP-50 and XP-OPAL50 CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand Connectors XP-50 / XP-OPAL50 XP-65 / XP-OPAL65Power Input CinemaWall Remote Control Surround buttonControls and Functions Other surfaces InstallationRemote Control Installation specialist Quick SetupInstallation must be performed by a qualified custom video Step Procedure For Details, refer toInstallation Considerations Ambient Light VentilationOther Considerations CinemaWall Connecting SourceConnections to Components toDVD Analog RGB Connections RS-232 Controller Connecting External Speakers OptionalConnector Pin Assignments ConnectionAC Power Connection Operation Turning on the Power Changing the OSD LanguageSetting the Day and Time Setting the Computer Display Properties Selecting an Input Source Changing the Aspect Ratio Aspect ratio selection is saved independently for each input169 149Played at the left and right 43 431 linearly scalesSource image horizon Edges of the screenUsing Picture-In-Picture PIP Activating PIP Swapping the Main PIP ImagesScreen or Input Source Using the On-Screen MenusSelecting a PIP Target Changing the PIP Window PositionPOS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness CinemaWall memorizes position and size settings separately POS./SIZEOptions menu refer to page 50 is set to On Frequency is 108 MHz or greaterOr 1080p and the Aspect Ratio is set to 169 refer to SoundSET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Refer to Changing the OSD Language on Order to activate multi-display mode, you must first setOn hides joints between displays C D Transparency cannot be used when Insert is set to on Insert cannot be used when Transparency is set to onCommand Timer refer to Present Time Setup Refer to Setting the Day and Time onDVD3 Operation Return Change Refer toLevel see below Currently activeMULTI-DISPLAY is active When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when Picture menu is set to WarmOn page 21, the Clock Display setting has no effect Using Digital ZoomDuring the delay period, the power indicator flashes green Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the ScreenTroubleshooting Tips Symptom Possible Causes SolutionSerial Communications Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes ExamplesSerial Commands Hex DescriptionDamzoom IMSPC1 SSCFNC0 VDO VWBGCT-30 Serial Communications Specifications CinemaWall SpecificationsCinemaWall Dimensions 12.31 Supported Timings Supported Signal Timings by Input Specifications Appendix A. Default Settings Table A-1. Runco Factory Default Settings for CinemaWallDefault Settings Page 020-0970-01 Rev. a September