Installation Considerations | Runco XP-OPAL65, XP-OPAL50 specification

Installation

Proper installation of your CinemaWall will ensure the highest possible picture quality. Whether you are installing the CinemaWall temporarily or permanently, you should take the following into account to ensure that it performs optimally.

Due to the design of all plasma glass panels made by every manufacturer, and the interaction between ambient air pressure and the plasma gases contained inside of the panel, reliable operation of your plasma display cannot be assured during operation at certain high-altitude locations.

At higher elevations, each panel may react differently, depending upon the altitude, air pressure, humidity and other meteorological factors. If you are planning to use this product at a high-altitude location (above 9,000 feet), please contact Runco technical support for further information.

To install the CinemaWall, you will need either an optional table stand or wall-mounting kit.

If you do decide to wall-mount the CinemaWall, ensure that the wall-mount bracket is installed according to the instructions included with it. The wall must be capable of supporting a redundant weight factor five (5) times the weight of the display, or be reinforced.

Runco recommends that this be done by a custom installation specialist.

Use only a Runco-approved wall-mount kit, table stand or floor

Note pedestal that is specifically designed for your display. Refer to

Parts List on page 4 for ordering information.

3.3 Installation Considerations

High-Altitude Operation

Mounting the CinemaWall on a Wall or Table Stand

You can attach your optional mounts or stand to the CinemaWall in either of two ways:

• While it is upright.

CinemaWall Installation/Operation Manual

13

Image 27

Runco XP-OPAL65, XP-OPAL50 operation manual Installation Considerations

Contents

XP-65 XP-50Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. Default Settings List of Figures List of Figures Xiv Target Audience Carriage return must be used after each command or stringIntroduction About This Manual Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental information Key Features and Benefits Description, Features and Benefits Optional Accessories XP-50 and XP-OPAL50 Controls and Indicators Controls and FunctionsCinemaWall at a Glance Display Stand XP-50 / XP-OPAL50 XP-65 / XP-OPAL65 Connectors Power Input Surround button CinemaWall Remote Control Controls and Functions Installation Remote ControlOther surfaces Step Procedure For Details, refer to Quick SetupInstallation must be performed by a qualified custom video Installation specialist Installation Considerations Ventilation Ambient Light Other Considerations Components to Connecting SourceConnections to CinemaWall DVD Analog RGB Connections Connection Connecting External Speakers OptionalConnector Pin Assignments RS-232 Controller AC Power Connection Turning on the Power Changing the OSD Language Setting the Day and TimeOperation Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio 149 169 Edges of the screen 43 431 linearly scalesSource image horizon Played at the left and right Activating PIP Swapping the Main PIP Images Using Picture-In-Picture PIP Changing the PIP Window Position Using the On-Screen MenusSelecting a PIP Target Screen or Input Source POS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separately Frequency is 108 MHz or greater Options menu refer to page 50 is set to On Sound Or 1080p and the Aspect Ratio is set to 169 refer to SET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language on On hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to on Present Time Setup Refer to Setting the Day and Time on Command Timer refer to DVD3 Operation Refer to Return Change Currently active Level see below Picture menu is set to Warm When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when MULTI-DISPLAY is active Using Digital Zoom During the delay period, the power indicator flashes greenOn page 21, the Clock Display setting has no effect Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote Control Symptom Possible Causes Solution Troubleshooting Tips Examples Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes Serial Communications Hex Description Serial Commands Damzoom IMSPC1 SSCFNC0 VDO VWBGCT-30 Serial Communications CinemaWall Specifications Specifications CinemaWall Dimensions 12.31 Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default Settings Default Settings Page 020-0970-01 Rev. a September