Samsung ML-D1630A 3

3.1 <

Getting Started>

3 Getting Started

This chapter gives you step-by-step instructions for setting up the

machine.

This chapter includes:

• Setting up the hardware

• Setting up the network

• Using a wired network

• Using a wireless network

• Altitude adjustment

Setting up the hardware

This section shows the steps to set up the hardware which is explained

in the Quick Install Guide. Make sure you read Quick Install Guide and

complete following steps.

1Select a stable location.

Select a level, stable place with adequate space for air circulation.

Allow extra space to open covers and trays.

The area should be well-ventilated and away from direct sunlight or

sources of heat, cold, and humidity. Do not set the machine close to

the edge of your desk or table.

Printing is suitable for altitudes under 1,000 m (3,281 ft). Refer to

the altitude setting to optimize your printing. See page 3.9 for more

information.

Place the machine on a flat and stable surface for not letting it lean

more than 2 mm (0.08 inches). Otherwise, it may affect the printing

quality.

2Unpack the machine and check all the enclosed items.

3Remove the tape holding the machine tightly.

4Install both the toner cartridge.

5Load paper. (See "Loading paper in the tray" on page 4.5.)

6Make sure that all the cables are connected to the machine.

7Turn the machine on.

8Install the software. See Software section.

Caution

This equipment will be inoperable when mains power fails.

Note

When the printer driver is in installation process, the driver

installer detects the locale information of your operating

system, and sets the default paper size for your machine. If

you use the different Windows locale, you must change the

paper size of your machine for matching your commonly

used paper size. Go to the printer properties to change the

paper size after installation completes.

Caution

When you move the machine, do not tilt or turn it upside down.

Otherwise, the inside of the machine may be contaminated by

toner, which can cause damage to the machine or bad printing

quality.

5 Kg (11 lbs)

Contents

Main Page contact SAMSUNG worldwide Page C 1. Introduction 2. Software overview 3. Getting Started 4. Selecting and loading print media Page i About this users guide Finding more information ii Safety and Regulatory Information Important Precautions and Safety Information iii Environmental and Safety Consideration Laser Safety Statement Warning Ozone Safety California USA Only United States of America Federal Communications Commission (FCC) Intentional emitter per FCC Part 15 Declaration of Conformity (European Countries) Approvals and Certifications EC Certification Regulatory Compliance Statements Wireless Guidance Replacing the Fitted Plug (for UK Only) Important Green and Yellow: Earth Blue: Neutral Brown: Live OPENSSL LICENSE ORIGINAL SSLEAY LICENSE Page 1.1 < 1 Special features 1.2 < Machine overview Front view Page 1.4 < Control panel overview 2.1 < 2 Supplied software 2.2 < Printer driver features System requirements Windows Linux 2.3 < Macintosh 3.1 < 3 5 Kg (11 lbs) Setting up the hardware 3.2 < Setting up the network Supported network environments Using a wired network Printing Configuration report Setting IP address Network parameter setting Installing the software 3.4 < Using a wireless network Checking your Network Environments IP address Wireless Networks 3.5 < Printing Configuration report Setting IP address IP setting using the SetIP program Installing the program Starting the program Network parameter setting Restoring factory default settings Restoring factory default settings using SyncThru Web Service 3.7 < Configuring the machines wireless network Using SyncThru Web Service 3.8 < Installing the software 3.9 < Altitude adjustment 4.1 < 4 media Selecting print media 4.2 < Guidelines for selecting and storing print media 4.3 < Specifications on print media 4.4 < Guidelines for special print media 4.5 < Loading paper in the tray Changing the paper size in the tray Note 4.6 < Setting the paper size and type Note 5.1 < 5 Printing a document Canceling a print job 6.1 < 6 Printing a machine report Cleaning your machine Cleaning the outside Cleaning the inside 6.2 < Note Caution 6.3 < Maintaining the cartridge Toner cartridge storage Handling instructions Use of non-Samsung and refilled toner cartridge Estimated cartridge life 6.4 < Note Caution 6.5 < Replacing the toner cartridge Caution 6.6 < Note Caution Maintenance Parts 6.7 < Managing your machine from the website 7.1 < 7 Tips for avoiding paper jams Clearing paper jams In the paper feed area and rear the machine 7.2 < Caution 7.3 < Rear and inside the machine Caution Note 7.4 < Caution Note Caution 7.5 < In the exit area Caution 7.6 < 1 Caution 7.7 < Understanding display messages 7.8 < Solving other problems Paper feeding problems Printing problems 7.9 < Note: 7.10 < Printing quality problems 7.11 < 7.12 < Common Windows problems 7.13 < Common Linux problems Common Macintosh problems Note: 8.1 < 8 accessories Supplies How to purchase 9.1 < 9 Printer specifications General specifications 10.1 < 10 I C D E F Page SOFTWARE SECTION C INSTALLING PRINTER SOFTWARE IN WINDOWS BASIC PRINTING A DVANCED P SHARING THE PRINTER LOCALLY USING SMART PANEL USING YOUR PRINTER IN LINUX USING YOUR PRINTER WITH A MACINTOSH 4 1 Software in Windows Installing Printer Software Installing Software for Local Printing Typical Installation 5 Custom In sta ll ati on Page 7 Installing Software for Network Printing Typical Installation Page 9 Custom Installation T Reinstalling Printer Software If you installed the printer software for local printing and Removing Printer Software 2 Printing a Document Printing to a file (PRN) Printer Settings 14 Layout Tab Paper Orientation Paper Tab Source Scaling Printing Graphics Tab Extras Tab About Tab Printer Tab Using a Favorite Setting Using Help 3 Printing M ultiple Page s on One Sheet of Paper ( N -Up Printing) Printing Posters Prin ting a Re duced or Enlarg ed Document Fitting Your Document to a Selected Paper Size Using Watermarks Using an Existing Watermark Creating a W atermark Editing a Watermark Deleting a Watermark Using Overlays What is an Overlay? Creating a New Page Overlay Using a Page Overlay Deleting a Page Overlay 4 Locally Setting Up a Host Computer Setting Up a Client Computer Using Smart Panel 5 Understanding Smart Panel Toner Level Using Smart Panel Opening the Troubleshooting Guide Using Printer Settings Utility Using Onscreen Help File Changing the Smart Panel Program Settings 25 6 root Linux Getting Started Installing the Unified Linux Driver Uninstalling the Unified Linux Driver root Using SetIP program Starting the program Using the Un ified D r iver Configurator Opening the Un ified Driver Configurator 28 Printers Conf iguration Printers Tab Classes Tab Ports Configuration Configuring Printer Properties Printing a Document Printing from Applications 30 Printing Files lpr lpr <file_name> 31 7 a Macintosh Installing Software Installing the Printer driver Uninstalling software Using SetIP program Starting the program Setting Up the Printer For a Network-connected For a USB-connected 34 Printing Printing a Do cument Changing P r inter Settings Layout Printing Multiple Pages on One Sheet of Paper SOFTWARE SECTION I A D E F T U W