Samsung PS50A40 Changing the Mode, Connect the TV, PC and 3D IR Emitter as shown in the figure

1Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your computer.

2Connect a 3.5mm Stereo/2RCA cable between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer.

3Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV.

4Turn the TV on and set the source of the TV to HDMI2.

For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3D glasses.

Adjust the PC resolution: PS50A470: 1024 x 768@60Hz,1360 x 768@60Hz

Optimum PC resolution for PS50A470 is 1360x768. When 1024x768 signal is connected in 3D mode, the picture will be shown in 4:3 format with left and right side grey bars appeared.

The 3D IR Emitter communicates with the 3D glasses.

Therefore, the 3D IR Emitter should be located near the 3D glasses.

It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported.

When the power is turned on or off, the mode changes to the default (Off) and the Format is saved.

The 3D Effect is turned on or off regardless of the Picture Mode.

When 3D Effect is on, only the Contrast, Brightness, 3D Effect, and Reset picture menus are activated.

To use the 3D Effect function, a graphics card supporting 3D or 3D software is required.

The 3D glasses and the Emitter must be manufacturer by the same company.

If you play a game or watch TV while wearing the 3D glasses for long periods of time, you may experience eyestrain or a headache.

3D glasses (including the Emitter) not manufactured by Samsung may not be supported.

If you find the screen flickering while the 3D function is used, change the environmental lighting darker or turn off the fluorescent lamp to watch the screen for its best condition.

Changing the Mode

Changing the Mode will exchange the pictures for each eye by exchanging the left and right output signals.

1Connect the TV, PC and 3D IR Emitter as shown in the figure.

2Press the SOURCE button to select HDMI .

3Press the MENU button to display the menu.

Press the ▲ or ▼ button to select Picture, then press the ENTER button.

4Press the ▲ or ▼ button to select Picture, Option then press the ENTER button.

Press the ▲ or ▼ button to select 3D Effect then press the ENTER button.

5Press the ▲ or ▼ button to select Mode, then press the ENTER button.

Press the ▲ or ▼ button to select Off, Mode1, Mode2 or 2D Conversion then press the ENTER button.

•Off : Turns the 3D Effect function off.

•Mode1 : Mode 1 operates with right sync first.

•Mode2 : Mode 2 operates with left sync first.

•2D Conversion : Provides picture converted 3D to 2D.

You can choose this to watch 2D picture temporally when you feel dizzy, but you should choose “Off” to end 3D Effect completely.

If the 3D effect is not working properly, it means the Mode and 3D glasses may not be syncing properly. To put them in sync, switch to the other mode.

T V		Picture
	Mode			: Standard						
	Cell Light									7
	Contrast						95
	Brightness								45
	Sharpness							50
	Colour							50
	Tint	G50					R50
	Detailed Settings									
	Picture Options									
	Reset			: OK						
	Move		Enter			Return
T V	Picture Options
	Colour Tone			: Normal						
	Size			: Auto Wide						
	Screen Mode		: 16:9							
	Digital NR			: Auto						
	Real 100 Hz Demo : Off									
	DNle			: Off						
	HDMI Black Level			: Normal						
	Blue only mode			: Off						
	Screen Burn Protection									
	3D Effect
	Move		Enter			Return
T V		3D Effect
	Mode		:		Off
	Format		:		Mode1
					Mode2
					2D Conversion
	Move		Enter			Return
					Continued...

English - 23