Samsung PS50A40 user manual Listening through a Receiver, Check Points before Requesting Service

Listening through a Receiver

You can listen to sound through a receiver instead of the TV speaker.

1Press the MENU button to display the menu.

	Press the ▲ or ▼ button to select Input, then press the ENTER button.	TV	P 1
2	Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER		View TV
	button.		Select Device
3	Press the ▲ or ▼ button to select Receiver, then press the ENTER button.		Record
4	Press the ◄ or ► button to select to On, then press the ENTER button.		Menu on Device
	Now you can listen to sound through the receiver.		Device Operation
5	Press the EXIT button to exit.
			Receiver	:On
➢ When the receiver is set to On, you can listen to the TV sound through the 2-			Setup
	channel receiver.		Move	Enter
➢ If the receiver is exclusively for a home theater only (supporting audio only), it may
			Exit
	not appear in the device list.

➢In case of a content with copyright problems, listening through the receiver may not properly operate.

➢When listening through the receiver, there are restrictions for using the PIP and audio-related menu.













Check Points before Requesting Service

Symptom	Solution
Anynet+ does not work.	■ Check if the device is an Anynet+ device. The Anynet+ system
	supports Anynet+ devices only.
	■ Connect only one receiver.
	■ Check if the Anynet+ device power cord is properly connected.
	■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
	■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
	setup menu.
	■ Check whether the TV remote control is in TV mode.
	■ Check whether it is Anynet+ exclusive remote control.
	■ Anynet+ doesn’t work at a certain condition. (Searching channels)
	■ When connecting or removing the HDMI cable, please make sure
	to search devices again or restart your TV.
	■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.	■ Check if the Anynet+ device is properly connected to the TV and
	check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+
	Setup menu.
	■ Press the TV button on the TV remote control to switch to TV.
	Then press the TOOLS button to show the Anynet+ menu and
	select a menu you want.
I want to exit Anynet+.	■ Select View TV in Anynet+ menu.
	■ Press the SOURCE button on the TV remote control and select a
	device other than Anynet+ devices.
	■ Press any of P, CH LIST, and PRE-CHto change to the
	TV mode. (Note that the channel button operates only when a
	tuner-embedded Anynet+ device is not connected.)
The message Connecting to	■ You cannot use the remote control when you are configuring
Anynet+ device… appears	Anynet+ or switching to a view mode.
on the screen.	■ Use the remote control when the Anynet+ setting or switching to
	view mode is complete.
The Anynet+ device does	■ You cannot use the play function when Plug & Play is in progress.
not play.
The connected device is not	■ Check whether or not the device supports Anynet+ functions.
displayed.	■ Check whether or not the HDMI cable is properly connected.
	■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
	setup menu.
	■ Search Anynet+ devices again.
	■ You can connect an Anynet+ device using the HDMI cable only.
	Some HDMI cables may not support Anynet+ functions.
The TV programme cannot	■ Check whether the antenna jack on the recording device is
be recorded.	properly connected.

English - 35