WHAT’S Included, Master Card Cables | Samsung SSA-S2000W specification

WHAT’S INCLUDED

Check if the following items are included in the product package.

X Y Z

[\ ] ^ _ `

lzj W lu{

i

zzhTzYWWW

Main Unit

3.5x 40mm Screws (x4)

3.5x 12mm Screws (x4)

6 x 30mm Plastic Anchors (x4)

Template

xGn

Quick Guide

O-rings (x5)

Diodes (x2)

(UF4004, 1N4001~4007)

PRODUCT INTRODUCTION

tGj

Master Card (x1)

Cables (x4)

CD Manual

English _ 7

Image 7

Samsung SSA-S2000W user manual WHAT’S Included, Quick Guide Rings Diodes UF4004, 1N4001~4007, Master Card Cables

Contents

Imagine the possibilities Standalone Rfid Access Controller Safety information Safety information This device may not cause harmful interference, Important Safety Instructions Contents Contact Sensor alarm To specify the input mode for AUXTo specify the input mode for the Door To specify the use of the tamper alarm Product introduction Features Quick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables Front View AT a Glance Cable Color Scheme Installation and External Connection DC12V Cable Selection Connection Bypass Diode Connection Output Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened TTL Output Chime Bell Output Wiegand Output SetupInitialization Brown line with white stripes Hardware Forcible Initialization Forced Initialization with External Line Reader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/W Enabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure Mode To Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact Sensor To Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled Device Buttons and press ENT To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Default is set to not used To Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not Authenticated Enter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX 32 I/O Time Setup \ ` To Specify the TTL Output Operation Mode Advanced settingTo SET the Chime Bell Function To Specify the Chime Bell Operation Time To Specify the Input Mode for AUX 36 고급 설정 To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit Button To Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card User To Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Initial Values Other information Function Codes Sense if AUX 2 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from L to H Troubleshooting Troubleshooting √ RF Only Troubleshooting Check the operation status of the product √ Enter the command to delete the user 14 + ENTService center EInstall and use the product as usual CIf SSA-S2000 responds when you press the Exit button Using the keypadUnregistered numbers in 5 consecutive times default User cards to the factory default Consult with a qualiﬁed technician Irrelevant data is transferredDisconnection or short-circuit S2000 Product speciﬁcations Product Specifications Correct disposal of batteries in this product