Manuals / Sanyo / Computer Equipment / Projector

Sanyo Proj05 owner manual Network configuration, Setting Procedure

Models: Proj05

1 62

Download 62 pages 28.2 Kb

Page 13

Network configuration

Network configuration

Network configuration

Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “3. Basic setting and operation” (p.17-30). First, complete the settings described in this chapter before performing steps in “3. Basic setting and opera- tion.”

Setting Procedure

1.Select Network icon in the menu bar with the Point 7 8 buttons, and press SELECT button once.

2.Make sure that the Network mode is set to "On". If the mode is "Off", switch to ON with the Point 7 8 buttons. Then the Menu will disappear, the “Please wait...” message will appear, and switching operation will start. Switching will take a while and the projector’s LINK/ACT Lamp will be on or blink, and after completing the operation, the “Please wait...” message will disappear.

Network icon

Switches between on and off with the Point 7 8 buttons.

Side Terminals

LINK Lamp (Green) Light green when the projector is connected to the network correctly.

ACT Lamp (Orange) Blink orange when the projector is sending or receiving the data.

LAN Connection Terminal

ENGLISH

13

Image 13

Sanyo Proj05 owner manual Network configuration, Setting Procedure

Contents

Network Set-up and Operation Wired Setting Projector Set-up and OperationOwner’s Manual Compliance Federal Communications Commission Notice CAUTION IN USING THE PROJECTOR VIA NETWORKS Safety instructionsCAUTION IN USING NETWORK FUNCTION Chapter 2 Setup Procedures Table of contentsChapter 3 Basic Setting and Operation Chapter 4 Controlling the ProjectorPreparation ChapterENGLISH Web Management function +p.31 FeaturesE-Mail Alert function +p.25 InternetRequired operating environment for computers Network specifications of the projectorDisplay settings FeaturesUse of this manual Expression/AbbreviationTrademarks Cabling Between the Projector and a Hub or computer*1STEP 1 Connect the LAN and set the configuration Flow of installationSTEP 2 Network Configuration has completed Chapter 1 Preparation Describes how to configure the network Setup ProceduresChapter ENGLISHConnecting to an Ethernet cable Setting Procedure Network configurationSets IP address of the default gateway Router Network settingDescription according to your network environmentNetwork PIN code How to enter values with the screen 10-key palletNetwork information Network factory defaultThe numerical value is a setting example Network factory defaultENGLISH Chapter Basic Setting and Operation2 Login Login the setting page of the projector1 Enter the IP address Main setting page in the display 3 Display of main setting pageExample of the setting page How to use the setting pageTypes of setting Text box setting Pull-down menu settingCheck box setting Radio button settingHow to use the setting page ENGLISHChapter 3 Basic Setting and Operation Initial settingDescription Network PIN code setting Chapter 3 Basic Setting and Operation Network configurationDescription E-mail setting E-mail settingmenu and follow the below steps ENGLISH3 Setting SMTP authentication 1 Setting SMTP server and administrator address2 Registering and deleting E-mail addresses Enter the e-mail address onto Add e-mail address and click Set buttonError message for sending alert mail 4 Setting POP serverOption selection for sending alert mail When internal PJ temperature is too high Examples Type and contents of alert mailWhen PJ needs service When PJ lamp replacement time is reachedSNMP setting Check and delete the trap address Trap option settingChapter 3 Basic Setting and Operation Checking the registered trap address and deleting the addressENGLISH Chapter Controlling the ProjectorPower control and status check Power management is operating About projector conditionThe temperature of the projector became too high Projector detects abnormal temp. and sets into standby modeInput ControlAvailable selection at the RGBPC analog input SystemAvailable selection at the RGBPC digital, RGBAV HDCP, HDMI input Available selection at the Video/S-video/Scart inputImage mode Video Computer Image adjustmentInput source Chapter 4 Controlling the ProjectorENGLISH PC adjustmentControl DescriptionScreen setting Setting up the projectorClick Reset to return to the center posi Setting up the projectorClick Reset to reset the keystone correc ENGLISHChapter 4 Controlling the Projector SettingDescription Setting up the projector SettingENGLISH DescriptionVideo delay control....Sets the digital processing of the SettingChapter 4 Controlling the Projector Item DescriptionInformation InformationInformation ItemsInformation NetworkChapter 4 Controlling the Projector DescriptionIndication of the filter status Indication of the lamp statusENGLISH InformationChapter 4 Controlling the Projector Appendix ChapterConnection examples Use of telnet Web browser setting Technical data Q & APeer-To-Peer connection Examples of connectionChapter 5 Appendix Computer Name PC05Theater The gateway Router installed in the networkNetwork Group OfficeControl Use of telnetCommand list table When the word Hello is replied, login has been succeededEnter with ASCII 64-byte capital characters and one-byte characters close returnActive Script/JavaScript enable Web browser settingProxy setting Examples OS/Browsers ActiveScript settingWindows XP Professional Internet ExplorerUsing proxy server Proxy settingNot using proxy server Netscape Navigator JavaScript SettingProxy setting Using proxy server2 Select Advanced icon and then click Proxies Change Settings JavaScript enable settingMAC OS X v SafariQ Why doesn’t the setting page appear in my web browser? Installation/AccessQ How can I restrict access from the computer Password/Login Q How can I install several projectors?Q What should I do when I forget the IP address of the projector? Q What should I do when I forget the password Network PIN code?Operation Q Why am I not receiving E-mail alert messages?ting page Q What is the MAC address assigned to the projector? Q Can I control the projector by using the telnet application?Others Q What are the rules for IP address assignment?Version of the firmware Q Can I update the firmware of the projectorSO-KE2AL NETWORK OWNERS MANUAL