Manuals / Sanyo / Computer Equipment / Projector

Sanyo Proj05 owner manual English, Setting up the projector, Description

Models: Proj05

1 62

Download 62 pages 28.2 Kb

Page 41

Setting up the projector

Setting 2

Item	Description

Logo	Sets on or off the logo display on
	the screen during the startup. (User,
	Default, OFF)

Filter control........Scroll the filter. Click "Roll-up", a confir-

mation display appears, and then click "OK", the filter will be scrolled.

Fan speed control...Sets the running speed for the cooling fans. (Normal, Max)

Remote control....Selects the remote control code.

(Code1 - Code8)

Power management...Sets into the selected power manage- ment mode (OFF, Ready, Shutdown) if the input signal is interrupted and no control key is pressed for the specified period of time.

	*The specified time can be set 1 to 30
On start	min.
On start	Sets the power-on mode when the AC cord is connected to the outlet. (ON, OFF)
Key lock	Sets the prohibition of controls either Projector or Remote control. (OFF, Projector,
	Remote control)

PJ lock suspend...When the projector has a security of PIN code lock, disable this function temporarily by pressing Execute button.

Setting procedure

1.Turn off the projector , disconnect AC cord from the outlet and then connect AC cord again.

2.Access this page with the web browser.

3.Click Execute button on the PJ lock suspend.

Shutter

Sets the shutter operation. (ON: close, OFF: open)

Shutter management...Sets the shutter management operation.

Effect	Sets the effect to fade in or out at opening or closing the shutter. (OFF, L1, L2)
Release .......key Sets available keys to release the shutter. (Any, SHUTTER)
Time	Sets the specified period of time when the projector shuts down after the projector
	is left with the shutter closed.
	* The specified time can be set 5 to 480 min.

ENGLISH

41

Image 41

Contents

Owner’s Manual Wired Setting Projector Set-up and OperationNetwork Set-up and Operation Compliance Federal Communications Commission Notice CAUTION IN USING NETWORK FUNCTION Safety instructionsCAUTION IN USING THE PROJECTOR VIA NETWORKS Chapter 2 Setup Procedures Table of contentsChapter 3 Basic Setting and Operation Chapter 4 Controlling the ProjectorENGLISH ChapterPreparation Web Management function +p.31 FeaturesE-Mail Alert function +p.25 InternetRequired operating environment for computers Network specifications of the projectorDisplay settings FeaturesUse of this manual Expression/AbbreviationTrademarks Cabling Between the Projector and a Hub or computer*1STEP 2 Network Configuration has completed Flow of installationSTEP 1 Connect the LAN and set the configuration Chapter 1 Preparation Describes how to configure the network Setup ProceduresChapter ENGLISHConnecting to an Ethernet cable Setting Procedure Network configurationSets IP address of the default gateway Router Network settingDescription according to your network environmentNetwork PIN code How to enter values with the screen 10-key palletNetwork information Network factory defaultThe numerical value is a setting example Network factory defaultENGLISH Chapter Basic Setting and Operation1 Enter the IP address Login the setting page of the projector2 Login Main setting page in the display 3 Display of main setting pageExample of the setting page How to use the setting pageTypes of setting Text box setting Pull-down menu settingCheck box setting Radio button settingHow to use the setting page ENGLISHDescription Initial settingChapter 3 Basic Setting and Operation Network PIN code setting Description Network configurationChapter 3 Basic Setting and Operation E-mail setting E-mail settingmenu and follow the below steps ENGLISH3 Setting SMTP authentication 1 Setting SMTP server and administrator address2 Registering and deleting E-mail addresses Enter the e-mail address onto Add e-mail address and click Set buttonOption selection for sending alert mail 4 Setting POP serverError message for sending alert mail When internal PJ temperature is too high Examples Type and contents of alert mailWhen PJ needs service When PJ lamp replacement time is reachedSNMP setting Check and delete the trap address Trap option settingChapter 3 Basic Setting and Operation Checking the registered trap address and deleting the addressENGLISH Chapter Controlling the ProjectorPower control and status check Power management is operating About projector conditionThe temperature of the projector became too high Projector detects abnormal temp. and sets into standby modeInput ControlAvailable selection at the RGBPC analog input SystemAvailable selection at the RGBPC digital, RGBAV HDCP, HDMI input Available selection at the Video/S-video/Scart inputImage mode Video Computer Image adjustmentInput source Chapter 4 Controlling the ProjectorENGLISH PC adjustmentControl DescriptionScreen setting Setting up the projectorClick Reset to return to the center posi Setting up the projectorClick Reset to reset the keystone correc ENGLISHDescription SettingChapter 4 Controlling the Projector Setting up the projector SettingENGLISH DescriptionVideo delay control....Sets the digital processing of the SettingChapter 4 Controlling the Projector Item DescriptionInformation InformationInformation ItemsInformation NetworkChapter 4 Controlling the Projector DescriptionIndication of the filter status Indication of the lamp statusENGLISH InformationChapter 4 Controlling the Projector Appendix ChapterConnection examples Use of telnet Web browser setting Technical data Q & APeer-To-Peer connection Examples of connectionChapter 5 Appendix Computer Name PC05Theater The gateway Router installed in the networkNetwork Group OfficeControl Use of telnetCommand list table When the word Hello is replied, login has been succeededEnter with ASCII 64-byte capital characters and one-byte characters close returnProxy setting Web browser settingActive Script/JavaScript enable Examples OS/Browsers ActiveScript settingWindows XP Professional Internet ExplorerNot using proxy server Proxy settingUsing proxy server Netscape Navigator JavaScript SettingProxy setting Using proxy server2 Select Advanced icon and then click Proxies Change Settings JavaScript enable settingMAC OS X v SafariQ How can I restrict access from the computer Installation/AccessQ Why doesn’t the setting page appear in my web browser? Password/Login Q How can I install several projectors?Q What should I do when I forget the IP address of the projector? Q What should I do when I forget the password Network PIN code?ting page Q Why am I not receiving E-mail alert messages?Operation Q What is the MAC address assigned to the projector? Q Can I control the projector by using the telnet application?Others Q What are the rules for IP address assignment?Version of the firmware Q Can I update the firmware of the projectorSO-KE2AL NETWORK OWNERS MANUAL