Manuals / Sanyo / Computer Equipment / Projector

Sanyo Proj05 owner manual Setting up the projector, Screen setting

Models: Proj05

1 62

Download 62 pages 28.2 Kb

Page 38

Image 38

Chapter 4 Controlling the Projector

Setting up the projector

Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting] or [Setting] and then set up each set- ting.

Screen setting

This function is to adjust the screen mode or the lens functions of the projector.

Item	Description

Screen	Switches the screen mode. (Normal,
Ceiling	Zoom, True, Natural wide, Full, Custom)
Ceiling	Sets the image top/bottom and left/
Rear	right reversed. (ON, OFF)
Rear	Sets the image left/right reversed. (ON,
	OFF)

* See the next page for the description of other functions.

✐ Natural widecannot be selected when 720p, 1035i, 1080i, 1080p or 1080psf is selected in AV sys- tem menu.

Page 38

Image 38

Sanyo Proj05 owner manual Setting up the projector, Screen setting

Contents

Owner’s Manual Wired Setting Projector Set-up and OperationNetwork Set-up and Operation Compliance Federal Communications Commission Notice CAUTION IN USING NETWORK FUNCTION Safety instructionsCAUTION IN USING THE PROJECTOR VIA NETWORKS Chapter 3 Basic Setting and Operation Table of contentsChapter 2 Setup Procedures Chapter 4 Controlling the ProjectorENGLISH ChapterPreparation E-Mail Alert function +p.25 FeaturesWeb Management function +p.31 InternetDisplay settings Network specifications of the projectorRequired operating environment for computers FeaturesTrademarks Expression/AbbreviationUse of this manual Cabling Between the Projector and a Hub or computer*1STEP 2 Network Configuration has completed Flow of installationSTEP 1 Connect the LAN and set the configuration Chapter 1 Preparation Chapter Setup ProceduresDescribes how to configure the network ENGLISHConnecting to an Ethernet cable Network configuration Setting ProcedureDescription Network settingSets IP address of the default gateway Router according to your network environmentHow to enter values with the screen 10-key pallet Network PIN codeThe numerical value is a setting example Network factory defaultNetwork information Network factory defaultChapter Basic Setting and Operation ENGLISH1 Enter the IP address Login the setting page of the projector2 Login 3 Display of main setting page Main setting page in the displayTypes of setting Text box setting How to use the setting pageExample of the setting page Pull-down menu settingHow to use the setting page Radio button settingCheck box setting ENGLISHDescription Initial settingChapter 3 Basic Setting and Operation Network PIN code setting Description Network configurationChapter 3 Basic Setting and Operation menu and follow the below steps E-mail settingE-mail setting ENGLISH2 Registering and deleting E-mail addresses 1 Setting SMTP server and administrator address3 Setting SMTP authentication Enter the e-mail address onto Add e-mail address and click Set buttonOption selection for sending alert mail 4 Setting POP serverError message for sending alert mail When PJ needs service Examples Type and contents of alert mailWhen internal PJ temperature is too high When PJ lamp replacement time is reachedSNMP setting Chapter 3 Basic Setting and Operation Trap option settingCheck and delete the trap address Checking the registered trap address and deleting the addressChapter Controlling the Projector ENGLISHPower control and status check The temperature of the projector became too high About projector conditionPower management is operating Projector detects abnormal temp. and sets into standby modeControl InputAvailable selection at the RGBPC digital, RGBAV HDCP, HDMI input SystemAvailable selection at the RGBPC analog input Available selection at the Video/S-video/Scart inputInput source Image adjustmentImage mode Video Computer Chapter 4 Controlling the ProjectorControl PC adjustmentENGLISH DescriptionSetting up the projector Screen settingClick Reset to reset the keystone correc Setting up the projectorClick Reset to return to the center posi ENGLISHDescription SettingChapter 4 Controlling the Projector ENGLISH SettingSetting up the projector DescriptionChapter 4 Controlling the Projector SettingVideo delay control....Sets the digital processing of the Item DescriptionInformation InformationInformation ItemsChapter 4 Controlling the Projector NetworkInformation DescriptionENGLISH Indication of the lamp statusIndication of the filter status InformationChapter 4 Controlling the Projector Connection examples Use of telnet Web browser setting Technical data ChapterAppendix Q & AChapter 5 Appendix Examples of connectionPeer-To-Peer connection Computer Name PC05Network Group The gateway Router installed in the networkTheater OfficeUse of telnet ControlEnter with ASCII 64-byte capital characters and one-byte characters When the word Hello is replied, login has been succeededCommand list table close returnProxy setting Web browser settingActive Script/JavaScript enable Windows XP Professional ActiveScript settingExamples OS/Browsers Internet ExplorerNot using proxy server Proxy settingUsing proxy server Proxy setting JavaScript SettingNetscape Navigator Using proxy serverMAC OS X v JavaScript enable setting2 Select Advanced icon and then click Proxies Change Settings SafariQ How can I restrict access from the computer Installation/AccessQ Why doesn’t the setting page appear in my web browser? Q What should I do when I forget the IP address of the projector? Q How can I install several projectors?Password/Login Q What should I do when I forget the password Network PIN code?ting page Q Why am I not receiving E-mail alert messages?Operation Others Q Can I control the projector by using the telnet application?Q What is the MAC address assigned to the projector? Q What are the rules for IP address assignment?Q Can I update the firmware of the projector Version of the firmwareNETWORK OWNERS MANUAL SO-KE2AL