Manuals / Sanyo / Computer Equipment / Projector

Sanyo Proj05 Features, Web Management function +p.31, E-Mail Alert function +p.25, Internet

Models: Proj05

1 62

Download 62 pages 28.2 Kb

Page 6

Image 6

Chapter 1 Preparation

Features

Web Management function (+p.31)

With this function, you can monitor projector functions such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer.

PC1	PC2	Turn on PJ1
		Turn on PJ1
		Internet	PJ2	PJ1
PC3	PC4	Internet
PC3	PC4	Intranet
		Intranet	PC5
			PC5

E-Mail Alert function (+p.25)

The projector sends messages to the registered e-mail addresses when a lamp abnormal- ity or power failure occurs with the projector. This message describes how to solve the cause of the problems. You can take efficient action for quick recovery.

PC1 PC2

PC3 PC4

Internet Intranet

PJ2PJ1

PC5

You've got Mail

Page 6

Image 6

Sanyo Proj05 owner manual Features, Web Management function +p.31, E-Mail Alert function +p.25, Internet Intranet

Contents

Wired Setting Projector Set-up and Operation Network Set-up and OperationOwner’s Manual Compliance Federal Communications Commission Notice Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKSCAUTION IN USING NETWORK FUNCTION Chapter 3 Basic Setting and Operation Table of contentsChapter 2 Setup Procedures Chapter 4 Controlling the ProjectorChapter PreparationENGLISH E-Mail Alert function +p.25 FeaturesWeb Management function +p.31 InternetDisplay settings Network specifications of the projectorRequired operating environment for computers FeaturesTrademarks Expression/AbbreviationUse of this manual Cabling Between the Projector and a Hub or computer*1Flow of installation STEP 1 Connect the LAN and set the configurationSTEP 2 Network Configuration has completed Chapter 1 Preparation Chapter Setup ProceduresDescribes how to configure the network ENGLISHConnecting to an Ethernet cable Network configuration Setting ProcedureDescription Network settingSets IP address of the default gateway Router according to your network environmentHow to enter values with the screen 10-key pallet Network PIN codeThe numerical value is a setting example Network factory defaultNetwork information Network factory defaultChapter Basic Setting and Operation ENGLISHLogin the setting page of the projector 2 Login1 Enter the IP address 3 Display of main setting page Main setting page in the displayTypes of setting Text box setting How to use the setting pageExample of the setting page Pull-down menu settingHow to use the setting page Radio button settingCheck box setting ENGLISHInitial setting Chapter 3 Basic Setting and OperationDescription Network PIN code setting Network configuration Chapter 3 Basic Setting and OperationDescription menu and follow the below steps E-mail settingE-mail setting ENGLISH2 Registering and deleting E-mail addresses 1 Setting SMTP server and administrator address3 Setting SMTP authentication Enter the e-mail address onto Add e-mail address and click Set button4 Setting POP server Error message for sending alert mailOption selection for sending alert mail When PJ needs service Examples Type and contents of alert mailWhen internal PJ temperature is too high When PJ lamp replacement time is reachedSNMP setting Chapter 3 Basic Setting and Operation Trap option settingCheck and delete the trap address Checking the registered trap address and deleting the addressChapter Controlling the Projector ENGLISHPower control and status check The temperature of the projector became too high About projector conditionPower management is operating Projector detects abnormal temp. and sets into standby modeControl InputAvailable selection at the RGBPC digital, RGBAV HDCP, HDMI input SystemAvailable selection at the RGBPC analog input Available selection at the Video/S-video/Scart inputInput source Image adjustmentImage mode Video Computer Chapter 4 Controlling the ProjectorControl PC adjustmentENGLISH DescriptionSetting up the projector Screen settingClick Reset to reset the keystone correc Setting up the projectorClick Reset to return to the center posi ENGLISHSetting Chapter 4 Controlling the ProjectorDescription ENGLISH SettingSetting up the projector DescriptionChapter 4 Controlling the Projector SettingVideo delay control....Sets the digital processing of the Item DescriptionInformation InformationInformation ItemsChapter 4 Controlling the Projector NetworkInformation DescriptionENGLISH Indication of the lamp statusIndication of the filter status InformationChapter 4 Controlling the Projector Connection examples Use of telnet Web browser setting Technical data ChapterAppendix Q & AChapter 5 Appendix Examples of connectionPeer-To-Peer connection Computer Name PC05Network Group The gateway Router installed in the networkTheater OfficeUse of telnet ControlEnter with ASCII 64-byte capital characters and one-byte characters When the word Hello is replied, login has been succeededCommand list table close returnWeb browser setting Active Script/JavaScript enableProxy setting Windows XP Professional ActiveScript settingExamples OS/Browsers Internet ExplorerProxy setting Using proxy serverNot using proxy server Proxy setting JavaScript SettingNetscape Navigator Using proxy serverMAC OS X v JavaScript enable setting2 Select Advanced icon and then click Proxies Change Settings SafariInstallation/Access Q Why doesn’t the setting page appear in my web browser?Q How can I restrict access from the computer Q What should I do when I forget the IP address of the projector? Q How can I install several projectors?Password/Login Q What should I do when I forget the password Network PIN code?Q Why am I not receiving E-mail alert messages? Operationting page Others Q Can I control the projector by using the telnet application?Q What is the MAC address assigned to the projector? Q What are the rules for IP address assignment?Q Can I update the firmware of the projector Version of the firmwareNETWORK OWNERS MANUAL SO-KE2AL