Manuals / Sanyo / Computer Equipment / Projector

Sanyo Proj05 owner manual Setting POP server, Error message for sending alert mail

Models: Proj05

1 62

Download 62 pages 28.2 Kb

Page 27

4Setting POP server

E-mail setting

4Setting POP server

When "POP before SMTP" is selected at "Auth" of "SMTP Authentication setting", enter "POP server*2" and "POP server port" and click Set button.

*2 The POP server is a server for receiving e-mail.

Please contact your network administrator to have this POP server address.

Error message for sending alert mail

When the projector has an abnormality, an alert message will be sent to the registered E-mail address.

If the SMTP server is missing or the authen- tication is not completed because of input error in E-mail address setting or SMTP authentication setting when sending alert e-mail, the error message will be displayed. Please check the respective settings.

Option selection for sending alert mail

Click Option sub menu tab. Check the con- dition items under which alert mail will be sent and click Set button.

Please refer to item "Examples :Type and contents of alert mail" described on the next page.

Error message for missing SMTP server

Error information

Error message for authentication problem

Error information

Option

✐"When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the side control or the remote control.

✐Up to 99,999 hours can be set for use time.

ENGLISH

27

Image 27

Sanyo Proj05 owner manual Setting POP server, Error message for sending alert mail, Option selection for sending alert mail

Contents

Wired Setting Projector Set-up and Operation Network Set-up and OperationOwner’s Manual Compliance Federal Communications Commission Notice Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKSCAUTION IN USING NETWORK FUNCTION Chapter 4 Controlling the Projector Table of contentsChapter 2 Setup Procedures Chapter 3 Basic Setting and OperationChapter PreparationENGLISH Internet FeaturesWeb Management function +p.31 E-Mail Alert function +p.25Features Network specifications of the projectorRequired operating environment for computers Display settingsCabling Between the Projector and a Hub or computer*1 Expression/AbbreviationUse of this manual TrademarksFlow of installation STEP 1 Connect the LAN and set the configurationSTEP 2 Network Configuration has completed Chapter 1 Preparation ENGLISH Setup ProceduresDescribes how to configure the network ChapterConnecting to an Ethernet cable Setting Procedure Network configurationaccording to your network environment Network settingSets IP address of the default gateway Router DescriptionNetwork PIN code How to enter values with the screen 10-key palletNetwork factory default Network factory defaultNetwork information The numerical value is a setting exampleENGLISH Chapter Basic Setting and OperationLogin the setting page of the projector 2 Login1 Enter the IP address Main setting page in the display 3 Display of main setting pagePull-down menu setting How to use the setting pageExample of the setting page Types of setting Text box settingENGLISH Radio button settingCheck box setting How to use the setting pageInitial setting Chapter 3 Basic Setting and OperationDescription Network PIN code setting Network configuration Chapter 3 Basic Setting and OperationDescription ENGLISH E-mail settingE-mail setting menu and follow the below stepsEnter the e-mail address onto Add e-mail address and click Set button 1 Setting SMTP server and administrator address3 Setting SMTP authentication 2 Registering and deleting E-mail addresses4 Setting POP server Error message for sending alert mailOption selection for sending alert mail When PJ lamp replacement time is reached Examples Type and contents of alert mailWhen internal PJ temperature is too high When PJ needs serviceSNMP setting Checking the registered trap address and deleting the address Trap option settingCheck and delete the trap address Chapter 3 Basic Setting and OperationENGLISH Chapter Controlling the ProjectorPower control and status check Projector detects abnormal temp. and sets into standby mode About projector conditionPower management is operating The temperature of the projector became too highInput ControlAvailable selection at the Video/S-video/Scart input SystemAvailable selection at the RGBPC analog input Available selection at the RGBPC digital, RGBAV HDCP, HDMI inputChapter 4 Controlling the Projector Image adjustmentImage mode Video Computer Input sourceDescription PC adjustmentENGLISH ControlScreen setting Setting up the projectorENGLISH Setting up the projectorClick Reset to return to the center posi Click Reset to reset the keystone correcSetting Chapter 4 Controlling the ProjectorDescription Description SettingSetting up the projector ENGLISHItem Description SettingVideo delay control....Sets the digital processing of the Chapter 4 Controlling the ProjectorItems InformationInformation InformationDescription NetworkInformation Chapter 4 Controlling the ProjectorInformation Indication of the lamp statusIndication of the filter status ENGLISHChapter 4 Controlling the Projector Q & A ChapterAppendix Connection examples Use of telnet Web browser setting Technical dataComputer Name PC05 Examples of connectionPeer-To-Peer connection Chapter 5 AppendixOffice The gateway Router installed in the networkTheater Network GroupControl Use of telnetclose return When the word Hello is replied, login has been succeededCommand list table Enter with ASCII 64-byte capital characters and one-byte charactersWeb browser setting Active Script/JavaScript enableProxy setting Internet Explorer ActiveScript settingExamples OS/Browsers Windows XP ProfessionalProxy setting Using proxy serverNot using proxy server Using proxy server JavaScript SettingNetscape Navigator Proxy settingSafari JavaScript enable setting2 Select Advanced icon and then click Proxies Change Settings MAC OS X vInstallation/Access Q Why doesn’t the setting page appear in my web browser?Q How can I restrict access from the computer Q What should I do when I forget the password Network PIN code? Q How can I install several projectors?Password/Login Q What should I do when I forget the IP address of the projector?Q Why am I not receiving E-mail alert messages? Operationting page Q What are the rules for IP address assignment? Q Can I control the projector by using the telnet application?Q What is the MAC address assigned to the projector? OthersVersion of the firmware Q Can I update the firmware of the projectorSO-KE2AL NETWORK OWNERS MANUAL