Manuals / Sanyo / Computer Equipment / Projector

Sanyo Proj05 owner manual Network PIN code setting

Models: Proj05

1 62

Download 62 pages 28.2 Kb

Page 23

Image 23

Initial setting

Network PIN code setting

This is to set the Network PIN code to restrict the access from an unauthorized person through the network.

Enter a 4-digit number as the Network PIN code onto the text box and click Set button. The projector begins restarting and it takes

about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. This is to perform the login authentication firmly.

The default Network PIN code [0000] means no Network PIN code is set.

✐When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a four-digit number is valid for the Network PIN code.

ENGLISH

Page 23

Image 23

Sanyo Proj05 owner manual Network PIN code setting

Contents

Owner’s Manual Wired Setting Projector Set-up and OperationNetwork Set-up and Operation Compliance Federal Communications Commission Notice CAUTION IN USING NETWORK FUNCTION Safety instructionsCAUTION IN USING THE PROJECTOR VIA NETWORKS Chapter 4 Controlling the Projector Table of contentsChapter 2 Setup Procedures Chapter 3 Basic Setting and OperationENGLISH ChapterPreparation Internet FeaturesWeb Management function +p.31 E-Mail Alert function +p.25Features Network specifications of the projectorRequired operating environment for computers Display settingsCabling Between the Projector and a Hub or computer*1 Expression/AbbreviationUse of this manual TrademarksSTEP 2 Network Configuration has completed Flow of installationSTEP 1 Connect the LAN and set the configuration Chapter 1 Preparation ENGLISH Setup ProceduresDescribes how to configure the network ChapterConnecting to an Ethernet cable Setting Procedure Network configurationaccording to your network environment Network settingSets IP address of the default gateway Router DescriptionNetwork PIN code How to enter values with the screen 10-key palletNetwork factory default Network factory defaultNetwork information The numerical value is a setting exampleENGLISH Chapter Basic Setting and Operation1 Enter the IP address Login the setting page of the projector2 Login Main setting page in the display 3 Display of main setting pagePull-down menu setting How to use the setting pageExample of the setting page Types of setting Text box settingENGLISH Radio button settingCheck box setting How to use the setting pageDescription Initial settingChapter 3 Basic Setting and Operation Network PIN code setting Description Network configurationChapter 3 Basic Setting and Operation ENGLISH E-mail settingE-mail setting menu and follow the below stepsEnter the e-mail address onto Add e-mail address and click Set button 1 Setting SMTP server and administrator address3 Setting SMTP authentication 2 Registering and deleting E-mail addressesOption selection for sending alert mail 4 Setting POP serverError message for sending alert mail When PJ lamp replacement time is reached Examples Type and contents of alert mailWhen internal PJ temperature is too high When PJ needs serviceSNMP setting Checking the registered trap address and deleting the address Trap option settingCheck and delete the trap address Chapter 3 Basic Setting and OperationENGLISH Chapter Controlling the ProjectorPower control and status check Projector detects abnormal temp. and sets into standby mode About projector conditionPower management is operating The temperature of the projector became too highInput ControlAvailable selection at the Video/S-video/Scart input SystemAvailable selection at the RGBPC analog input Available selection at the RGBPC digital, RGBAV HDCP, HDMI inputChapter 4 Controlling the Projector Image adjustmentImage mode Video Computer Input sourceDescription PC adjustmentENGLISH ControlScreen setting Setting up the projectorENGLISH Setting up the projectorClick Reset to return to the center posi Click Reset to reset the keystone correcDescription SettingChapter 4 Controlling the Projector Description SettingSetting up the projector ENGLISHItem Description SettingVideo delay control....Sets the digital processing of the Chapter 4 Controlling the ProjectorItems InformationInformation InformationDescription NetworkInformation Chapter 4 Controlling the ProjectorInformation Indication of the lamp statusIndication of the filter status ENGLISHChapter 4 Controlling the Projector Q & A ChapterAppendix Connection examples Use of telnet Web browser setting Technical dataComputer Name PC05 Examples of connectionPeer-To-Peer connection Chapter 5 AppendixOffice The gateway Router installed in the networkTheater Network GroupControl Use of telnetclose return When the word Hello is replied, login has been succeededCommand list table Enter with ASCII 64-byte capital characters and one-byte charactersProxy setting Web browser settingActive Script/JavaScript enable Internet Explorer ActiveScript settingExamples OS/Browsers Windows XP ProfessionalNot using proxy server Proxy settingUsing proxy server Using proxy server JavaScript SettingNetscape Navigator Proxy settingSafari JavaScript enable setting2 Select Advanced icon and then click Proxies Change Settings MAC OS X vQ How can I restrict access from the computer Installation/AccessQ Why doesn’t the setting page appear in my web browser? Q What should I do when I forget the password Network PIN code? Q How can I install several projectors?Password/Login Q What should I do when I forget the IP address of the projector?ting page Q Why am I not receiving E-mail alert messages?Operation Q What are the rules for IP address assignment? Q Can I control the projector by using the telnet application?Q What is the MAC address assigned to the projector? OthersVersion of the firmware Q Can I update the firmware of the projectorSO-KE2AL NETWORK OWNERS MANUAL