Press MENU and the MENU screen displays. Press c/d to select “Setup”.
Repeat steps 1 to 4 in Programme Setup. Press a/b to select “Yes”, and then press OK.
Repeat steps 1 to 4 in Programme Setup. Press a/b to select “Yes”, and then press OK.

Menu operations

Sort

Channel positions can be sorted freely.

1

2

3 Press a/b/c/d to select the channel you want to move, and then press OK.

4 Press a/b/c/d to move it to the desired position, and then press OK.

5 Repeat steps 3 and 4 until all desired channels are sorted.

Erase Programme

An individual programme can be erased.

1

2

3 Press a/b/c/d to select the channel you want to erase, and then press OK.

4 Press OK to erase the selected programme. All the subsequent programmes move up.

5 Repeat steps 3 and 4 until all desired channels are erased.

Child Lock

TV only

 

 

Allows you to use a PIN to protect certain settings from being accidentally changed.

Changing the PIN

1

2

3 Press a/b to select “Child Lock”, and then press OK. If you have already set the PIN under “Child Lock”, enter it here.

Change PIN

Reset

New PIN

Reconfirm

 

 

 

 

 

 

 

 

 

Resetting the PIN

Allows you to reset your PIN to the factory preset “1234”.

1 Repeat steps 1 to 3 in Changing the PIN.

2 Press a/b to select “Reset”, and then press OK. 3 Press a/b to select “Yes”, and then press OK.

NOTE

As a precautionary measure, make a note of your PIN on the back of this operation manual, cut it out and keep it in a safe place that children cannot reach.

See page 25 for resetting the current PIN to the factory preset “1234” if you lose or forget your PIN.

To relock a channel which has been temporarily unlocked by inputting the correct PIN, turn power off and then on again.

Input Label

You can assign each input source a label you like.

1 Press b to select the desired input source.

2 Press MENU and the MENU screen displays.

3 Press c/d to select “Setup”.

4 Press a/bto select “Input Label”, and then press OK.

5 Press a/bto select characters and c/dto move to the desired digit to label the input source.

When you want to change the input label to the default name, select “CLEAR” on the “Input Label” screen.

6 Repeat step 5 above until the name is fully spelt out, and then press OK.

The name can be 6 characters or less.

When you want to set an input source name of less than 6 characters, press MENU to exit from the labelling menu.

NOTE

You cannot change the label if the input source is TV or DTV.

Position

TV/DTV/AV only

 

 

Menu Operation: C (page 9)

4 Press a/b to select “Change PIN”, and enter the 4-digit number as a PIN using 09.

5 Enter the same 4-digit number as in step 4 to confirm.

When setting the PIN, “Reset” in the Menu will be selectable and operational.

For adjusting a picture’s horizontal and vertical position.

Item

H-Pos.:Centres the image by moving it to the left or right.

V-Pos.:Centres the image by moving it up or down.

NOTE

To view a locked channel (Lock setting in Programme Setup “Manual Adjust” is set to “On”), you must enter a PIN. (See page 13 and page 19 for locking channels from viewing in analogue TV and DTV mode.) When you select a locked channel, a PIN prompt message pops up. Press OK to display the PIN input window.

NOTE

Adjustments are stored separately according to input source.

Depending on the input signal type a position setting may not be available.

14

Page 16
Image 16
Sharp LC-19D1S, LC-19D1E operation manual Sort, Erase Programme, Input Label, Changing the PIN, Resetting the PIN