No Signal, Tr. Protect | Sharp MD-MT866H instruction

ERROR MESSAGES		MEANING		REMEDY
NO DISC		● A disc has not been loaded.		● Load a disc.
NO SIGNAL		● Poor connection of the digital cable.		● Connect the digital cable securely.
(noSIG.)		● No output signal comes out from the con-		● If the portable CD player has a function to prevent sound skips,
		nected unit to playback.		deactivate it.
		● The input signal has improper sampling		● Playback with the connected unit.
		frequency.
PLAY MD		● You recorded on a playback-only disc.		● Replace it with a recordable disc.
(PLAYmd)
POWER ?		● The battery charger is defective.		● To have it repaired, go to the distributor where you purchased
				the unit.
PROTECTED		● The write protection tab of a MiniDisc is		● Move the write protection tab back to its original position.
		set to the protected position.		● Replace it with a recordable MiniDisc.
		● You tried to record on a playback-only disc.
SORRY		● Since a track number is currently being		● Wait for a while and try the operation again.
(SORRY)		located or updated, the unit cannot accept
		your command.
TEMP OVER		● The temperature is too high.		● Turn off the power, and wait for a while.
(TEMP!)
TOC FORM **		● There is an error in the recording signal.		● Erase all of the tracks, and then record again.
(Tform**)
TOC FULL		● There is no space left for recording char-		● Replace it with another recordable disc.
		acter information (track names, disc
		names, etc.).
Tr. Protect		● The track has been protected from being		● Edit the track with the device on which it was recorded.
		erased.
? DISC		● A disc which contains data other than		● A disc which contains non-music data cannot be played.
(? DISC)		music was played.		● Replace it with another recorded disc.
		● There is an error in the signal recorded
		on the disc.
		● Stamping is not possible.		● Retry.

( ) : Error messages seen on the remote control. Number or symbol appears in * position.

Web-site:www.sharp.co.uk/support Help Line: 08705 274277 (office hours)

References

– Error Messages –

51

Image 51

Sharp MD-MT866H operation manual No Signal, Tr. Protect

Contents

Thank you for purchasing this Sharp product MD-MT866H Accessories Contents Special Notes Important IntroductionSpecial Notes Introduction Storing the unit PrecautionsPrecautions Avoid using or leaving the unit in the following places Main unit Names of Controls and Indicators Main unit display panel Important Introduction Names of Controls and Indicators Names Remote control unitRemote control display panel Indicators Battery Charger Battery- Charger Names SettingFace the top Charge Toward you Mode For use with the AC adaptor How to use the Charge / Operation switchBattery Removing Using with the Rechargeable Battery Power Source Using with the Rechargeable BatteryCharging Power About the liquid crystal display LCD About charging timeDisplay Conditions Source Using with the AC AdaptorUsing with Operation mode Release Lock Open Press Hold Function PreparationHold Function Inserting a MiniDisc Inserting a MiniDisc To the DC in 5V socket To the Optical Line in socket ConnectionsConnections You can record your favorite CDs or tapes to an MD To the DC 50/60Hz 5V socket To the wall socketTo the Optical Line in socket Recording Basic Operation RecordingBefore Recording Press the REC button Digital recording+12 -12dB About the TOC To update the recorded contents of the MiniDiscTo interrupt recording To stop recording Basic Helpful tip when attaching a labelOperation Recording Before Playing back PlaybackBasic Playback To interrupt playback Volume controlTo turn off the power Bass control To locate the beginning of a track Advanced Playback To return to normal playback Useful Features Advanced PlaybackRandom play or repeat play To interrupt fast playback Advanced Recording Start recording Useful Features Advanced RecordingPress the Mode button whilst the record- ing is paused Long-play recording monaural recording You can erase a portion of a track and make a new recording Press the right shuttle switch toward ENTER/SYNC You can create your own track numbers at any point When a recording is paused or whilst recording…To create your own track numbers Recording tracks as a single track About sampling rate converter About track numbers To record from a microphone Useful Features Recording from a MicrophoneTo write recorded contents on the MiniDisc Recording from a Microphone Recording from a Microphone During a mic synchro recording UsefulTrack intervals During a mic manual recording During playback, press the Disp button Useful Features Checking DisplaysChecking Displays To check the elapsed time and remaining time of the track Press the Disp button to display the play To display the playing time of an indiVidual track Track number and track name Changing Changing Default SettingsFeatures Default Settings Auto play Display backlight on the remote controlAuto power save Beep sound Titling a Titling a MiniDiscAdvanced MiniDisc To add characters Characters symbolsTo erase a character To enter a space Before stamping What is a master MiniDisc?What is a MiniDisc for stamping? Stamping titles from another MiniDisc Operation of the MiniDisc for stamping To erase tracks one at a time Advanced FeaturesPress the right shuttle switch toward ENTER/SYNC again Editing a Recorded MiniDisc Press the Edit button repeatedly to select Combine To divide a trackTo combine tracks Press the Edit button repeatedly to select Divide To move a track AD-CA55X White Red Other Features and Caution References Other Features and Caution Resuming auto playRechargeable battery MiniDisc System Limitations Symptom Limitations Error Messages Error MessagesReferences Tr. Protect No Signal Troubleshooting Troubleshooting Moisture condensation MaintenanceMaintenance If trouble occurs Specifications Specifications Error correction DimensionsWeight Signal readout Sharp Corporation