I NSTALLATION

!WARNING:

Inspect the Oven:

Check the oven carefully for damage before and regularly after installation.

•Make sure the door closes properly, that it is not misaligned or warped.

•Check the hinges and door safety latches are not broken or loose.

•Ensure the door seal and sealing surfaces are not damaged.

•Inspect the oven interior and door for dents. Caution Sheet:

Always keep the caution sheet (Special Instructions and Warnings) close to the oven for your reference. Important:

If any damage is apparent, do not operate the oven in any way. Contact your dealer or an authorised Service Technician appointed by SHARP.

1Remove all packing materials. Remove the protective film (blue film) from the outer case cabinet (if covered). Do not remove the plastic film from the inside of the oven window as this protects it from dirt.

2Place oven on a secure, level surface, strong enough to take the oven weight, plus the heaviest item likely to be cooked in the oven.

Do not place this oven in a position which is not easily accessible. To position the oven too high can be dangerous because food can not be removed safely.

3Ensure there is a minimum free space above the oven of 25 cm.

4Do not place the oven where heat, moisture or high humidity are generated, (for example, near or above a conventional oven) or near combustible materials (for example, curtains). Do not block or obstruct air vent openings, as obstructions may ignite due to the emission of hot air.

5Make sure the power supply cord is undamaged and that it does not run under the oven or over any hot or sharp surfaces.

6The socket must be readily accessible so that it can be easily unplugged in an emergency.

7Do not use the oven outdoors.

8Two same oven models can be installed together by placing one on top of another. Follow these

instructions.

8-1) Place the oven A and position the oven B on top of the oven A as shown in the figure A.

8-2) Remove the single screw (a) holding the mounting plate A to the rear cabinet of the oven A. And remove the mounting plate A.

8-3) Remove the single screw (b) from the rear cabinet of the oven B, as shown in the figure A.

8-4) Reinstall the mounting plate A to the rear cabinet of the oven B with the single screw (b) removed, as shown in the figure A.

8-5) Hold the mounting plate A to the rear cabinet of the oven A with the single screw (a), as shown in the figure A.

8-6) Remove the screw (a) holding the mounting plate B to the rear cabinet of the oven B. And remove the mounting plate B from the oven B. See the figure A.

8-7) Install the screw (a) to its position again.

8-8) Remove the screw (c) from the oven A.

8-9) Remove the screw (d) from the oven B.

8-10) Turn the removed mounting plate B over and then using the removed screw (c) and (d), attach the mounting plate B, as shown in the figure A.

Figure A

 

Screw (a)

Oven B

 

 

 

Rear cabinet

Mounting plate A

 

 

 

Screw (b)

 

 

 

 

 

 

Screw (d)

Screw (a)

 

 

Screw (c)

 

 

 

 

 

 

Mounting plate B

WARNING:

Oven A

Rear cabinet

 

 

 

 

In situations where two ovens are installed together by placing one on top of another,

1)Use the two mounting plates for fixing the two ovens.

2)Make sure that the power supply cord is not caught between the two ovens.

3)Do not install more than one oven on top of another.

4)Do not lose the removed screws.

BUILDING-IN-KIT

This oven is not designed to be built into a kitchen unit.

IMPORTANT! ELECTRICAL CONNECTION

•Do not allow water to come into contact with the power supply cord or plug.

•Insert the plug properly into the socket as the plug may otherwise overheat and catch fire.

•Do not connect other appliances to the same socket using an adaptor plug as it may cause the wiring to overheat and catch fire.

•If the plug or socket is loose or the power supply cord is damaged, do not operate the oven, it must be replaced by the special power cord. Contact your dealer or a Service Technician appointed by SHARP. A defective plug, power supply cord or socket may overheat and catch fire during operation or cause an electrical shock.

•When removing the plug from the socket always grip the plug, never the mains lead as this may damage the power supply cord and the connections inside the plug.

•The product is fitted with a non-rewireable (moulded) plug. Should it not be suitable for the socket outlet in your kitchen, remove the plug and fit an appropriate type, observing the wiring code given in "To replace the mains plug" on page 30.

The fuse from a cut-off plug should be removed and the plug disposed of in safe manner. Under no circumstances should the cut-off plug be inserted into a socket outlet as serious electrical shock may occur. The plug must not be used without the fuse cover fitted.

When replacing the plug please ensure that you use a BSI or ASTA approved plug to BS1363, this should be fitted with a brown coloured 13 amp fuse approved by BSI or ASTA to BS1362. If you have any doubt about electrical connection seek the help of a qualified electrician.

!WARNING

THIS APPLIANCE MUST BE EARTHED.

To wire an appropriate plug, follow the wiring code given in "To replace the mains plug" on page 30.

5

Page 5 Page 7
Page 6
Image 6
Sharp R-24AT, R-22AT Nstallation, Building-In-Kit, IMPORTANT! Electrical Connection, This Appliance Must be Earthed
Page 5 Page 7

R-22AT, R-24AT specifications

The Sharp R-24AT and R-22AT microwave ovens are advanced kitchen appliances designed to enhance cooking convenience, efficiency, and versatility. Both models incorporate innovative technologies and features that cater to modern cooking needs.

The Sharp R-24AT boasts a robust 900 watts of cooking power, enabling users to prepare a wide variety of meals quickly and effectively. Its spacious 24-liter capacity is suitable for families and those who enjoy entertaining. One of the standout features of the R-24AT is its intelligent sensor technology, which automatically detects humidity levels in the cooking food. This innovative feature ensures optimal cooking times and temperatures, resulting in perfectly cooked dishes without the guesswork.

Another key technology in the R-24AT is the inverter cooking system. This system provides a seamless flow of power throughout the cooking process, allowing for more precise temperature control. Unlike traditional microwaves that operate in full power or off, inverter technology ensures consistent heat, which is particularly beneficial for tasks such as defrosting, reheating, and simmering.

The Sharp R-22AT, while slightly more compact with a 22-liter capacity, also delivers impressive performance with 800 watts of power. It features a similar inverter cooking system that guarantees even cooking results. Both models come with multiple auto-cook presets, providing users with a selection of quick options for common dishes such as popcorn, pizza, and oatmeal. This feature streamlines meal preparation and reduces the time spent on planning meals.

In addition, the user-friendly control panel on both models includes a combination of push-button and rotary dial controls for easy navigation. The inclusion of a bright LED display further enhances usability, allowing cooks to monitor cooking times and settings easily.

Safety is another critical aspect of the Sharp R-24AT and R-22AT. Both models come equipped with a child lock feature, ensuring peace of mind in homes with young children. The stainless steel interiors of these microwaves facilitate easy cleaning, while their sleek design adds a modern touch to any kitchen.

In summary, the Sharp R-24AT and R-22AT microwave ovens stand out for their advanced cooking technologies, user-friendly features, and thoughtful design. They empower home cooks to prepare meals with precision and ease, making them a valuable addition to any kitchen.
Top Page Image Contents