Remote control |
| General control |
■Display brightness control
■Battery installation
� Open the battery cover.
2� Insert the supplied battery according to the terminal indicated in the battery compartment.
3� When inserting or removing the battery, push it towards the
4� Close the cover.
Caution:
●Replace all old batteries with new ones at the same time.
●Do not mix old and new batteries.
●Remove the battery if the unit will not be used for a long period of time. This will prevent potential damage due to battery leakage.
●Do not use rechargeable battery
●Installing the battery incorrectly may cause the unit to malfunction.
●Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
Notes: concerning use:
●Replace the battery if the operating distance is reduced or if the operation becomes erratic. Purchase two “AAA” size batteries
●Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth.
●Exposing the sensor on the unit to strong light may interfere with operation. Change the lighting or the direction of the unit if this occurs.
●Keep the remote control away from moisture, heat, shock, and vibrations.
■Test of the remote control
Check the remote control after checking all the connections.
Point the remote control directly at the remote sensor on the unit. The remote control can be used within the range shown below:
Remote sensor
0.2 m - 6 m
(8” - 20’ )
■Turning the Power On
Press
Entering standby
Press
Note:
●When you turn on this unit for the first time after purchase or when you turn on this unit after you perform “System Reset” (see page 29), the language setting screen will be displayed, so please perform the language setting (see step 3 of page 13).
●If you press
About the Home screen
When turning on the unit on DISC function, the Home screen appears.
Home screen
|
|
|
| Video |
|
| |
|
|
|
| Music | USB |
|
|
1 |
|
|
| Picture | Home Network |
| |
|
|
|
| ||||
|
|
|
|
|
|
| |
|
|
|
| Settings |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Select | ENTER Enter | Return | EXIT Exit |
|
|
|
|
|
|
|
|
234 5
1�Main menu
2�Icon for disc inserted
3�Icon for USB memory device connected 4�Icon for LAN connection
5�Button Guide
E-12
To dim the display brightness, press and hold the DISPLAY <DIM> button on the remote control for more than 2 seconds.
●The display brightness will change each time the DISPLAY <DIM> button is pressed for more than 2 seconds.
Dimmer 1 | (Display is dim). |
Dimmer 2 | (Display gets dimmer). |
Dimmer off (Display is bright).
■Volume auto fade-in
If you turn off and on the main unit with the volume set to 80 or higher, the volume starts at 40 and fades in to the last set level.
■Volume control
Turn the volume knob towards VOLUME +/– (on main unit) or press VOL. +/– (on remote control) to increase or decrease the volume.
■Speaker output selection (HDMI connection)
By using HDMI connection, you have an option to listen to the sound output either from this unit or your TV.
To select the preferred speaker output, press and hold TV (ARC) button on the remote control until “TV Speaker” or “BD601 Speaker” appears on the display.
■Auto power on function
When you press any of the following buttons, the unit turns on.
●iPod <TV OUT>, DISC, INPUT, TUNER, TV (ARC) on the remote control: Selected function is activated.
●/ or OPEN/CLOSE button on the main unit: The unit turns on and playback of the last function will start (DISC, TUNER,
■Auto power off function
The main unit will enter the
DISC: In the stop mode.
AUDIO IN/LINE IN/DIGITAL IN/ TV ARC: No detection of input signal or very low sound audibility
Note:
However, if iPod or iPhone is docked, the unit will begin charging. “Charge Mode” will be displayed.
■Muting
The volume is muted temporarily when pressing the button on the remote control. Press again to restore the volume.
■X-Bass control
When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and
