Timer and sleep operation (Remote control only) (continued)
Enhancing your system
3�When the timer end time is reached, the system will enter the power
Once timer:
The timer will be cancelled.
Daily timer:
The timer operates at the same time every selected day. It will continue until the daily timer setting is cancelled. Cancel the daily timer when it is not in use.
Notes:
●When performing timer playback using another unit connected to the USB 2, AUDIO IN, LINE IN or DIGITAL IN socket select
●This unit will turn on or enter the power
Checking the timer setting:
� Turn the power on and press and hold down the CLOCK/TIMER button.
2� Within 10 seconds, press the 
or 
button to select “Once” or “Daily”, and press the ENTER button.
3� Within 10 seconds, press the 
or 
button to select “Timer Call”, and press the ENTER button.
Cancelling the timer setting:
� Turn the power on and press and hold down the CLOCK/TIMER button.
2� Within 10 seconds, press the 
or 
button to select “Once” or “Daily”, and press the ENTER button.
3� Within 10 seconds, press the 
or 
button to select “Timer Off”, and press the ENTER button. Timer will be cancelled (the setting will not be cancelled).
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To reuse the same setting, perform the following operations.
� Turn the power on and press and hold down the CLOCK/TIMER button.
2� Within 10 seconds, press the 
or 
button to select “Once” or “Daily”, and press the ENTER button.
3� Within 10 seconds, press the 
or 
button to select “Timer On” , and press the ENTER button.
4� Press the
■Sleep operation
The radio, disc, iPod, USB, Audio In, Line In, TV (ARC) and Digital In can all be turned off automatically.
� Play back the desired sound source.
2� Press the SLEEP button.
3� Within 5 seconds, press the Numeric button to set the time. (1 minute ~ 99 minutes)
4� “SLEEP” will appear.
5� The unit will enter the power
To confirm the remaining sleep time:
� Whilst “SLEEP” is indicated, press the SLEEP button.
To cancel the sleep operation:
Press the
� Whilst “SLEEP” is indicated, press the SLEEP button.
2� Within 5 seconds, press the “0” button twice until “SLEEP 00” appears.
■To use timer and sleep operation together
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up to iPod in the next morning.
� Set the sleep time (see above, steps 1 - 5).
2� Whilst the sleep timer is set, set the timer playback (steps 2 - 9, page 39).
Sleep timer | Timer playback | End | |||
setting | setting | time | |||
|
|
|
|
|
|
|
|
| Desired time |
| |
|
|
|
|
| |
| Sleep operation will | Timer playback | |||
| automatically stop | start time | |||
The connection lead is not included. Purchase a commercially available lead as shown below.
Portable audio unit, etc.
Audio cable (not supplied)
■Listening to the playback sounds of portable audio unit, etc.
� Use a connection lead to connect the portable audio unit etc. to the AUDIO IN socket. When using video equipment, connect the audio output to this unit and the video output to a television.
2� Press the
3� Press the INPUT button on the remote control or SELECTOR button repeatedly on main unit to select AUDIO IN function.
4� Play the connected equipment. If volume level of the connected device is too high, sound distortion may occur. Should this happen, lower the volume of the connected device. If volume level is too low, increase the volume of the connected device.
Note:
To prevent noise interference, place the unit away from the television.
■Headphones
●Do not turn the volume on to full at switch on and listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss.
●Before plugging in or unplugging the headphone, reduce the volume.
●Be sure your headphone has a 3.5 mm (1/8”) diameter plug and impedance between 16 and 50 ohms. The recommended impedance is 32 ohms.
●Plugging in the headphone disconnects the speakers automatically. Adjust the volume using the VOLUME control.
