9-2. Output Limitation
Please refer to the table below, because electric tools and home appliances cannot be judged only by the
rated.
The rated output or the power consumption due to the efficiency and character of components.
Applicable Load (For reference only)
|
|
|
|
|
|
|
|
|
|
|
| Capacity(kW) |
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
| Loads |
|
|
|
|
|
|
|
| 220V | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Receptacle |
| Terminal |
| Terminal | ＆ | Terminal | Total 3 terminal |
| ||
|
|
|
|
|
|
|
|
| Terminal | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 1pce |
|
| 1 set |
| receptacle | 1 set | set | ||
|
|
|
|
|
|
|
|
|
| total |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Electric Bulb, Heater, etc. |
|
|
|
| 1.5 |
|
| 3.0 |
| 6.0 |
| 6.0 | 8.0 |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Electric Tools, etc. (Series |
|
|
|
| 0.7 |
|
| 1.5 |
| 3.0 |
| 3.0 | 4.0 |
| ||
motor) |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Mercury Lamp (high power |
|
|
|
| 0.6 |
|
| 1.2 |
| 2.4 |
| 2.4 | 3.2 |
| ||
factor type) |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Submersible Pump, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Compressor, etc. (induction |
|
|
|
| 0.6 |
|
| 1.2 |
| 2.4 |
| 2.4 | 3.2 | 4.0 | ||
motor) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
－２６－ |
|
|
|
| Motor with brush |
|
|
|
|
| ||||||
Series Motor | ： |
|
|
|
|
| ||||||||||
Induction Motor | ： | Brushless Motor |
|
|
|
|
| |||||||||
The value described is | 『 | OUTPUT | for induction motor load and |
|
| |||||||||||
|
|
|
|
| 』 |
|
|
|
|
| ||||||
| POWER CONSUMPTION | for the other equipment. |
|
|
|
| ||||||||||
| 『 |
|
|
|
|
| 』 |
|
|
|
|
|
|
|
|
|
Caution |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
＜ |
| ＞ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Be sure to use the frequency designated in the equipment incorporated in mercury |
| ||||||||||||||
bulb or induction motor.
The load incorporated in motor may require bigger power than the rated power consumption.
So, consult with our authorized distributor or our engineering section to clarify.
When connection to use 2 or more sets, start the load one by one, not to start them simultaneously. When starting a mercury bulb ON again, wait for about 15 minutes until it cools down.
27
