Attaching the Brackets | SMC Networks SMC6724L3 INT specification

INSTALLING THE SWITCH

To rack-mount devices:

1.Attach the brackets to the device using the screws provided in the Bracket Mounting Kit.

Figure 3-1. Attaching the Brackets

2.Mount the device in the rack, using four rack-mounting screws (not provided).

Figure 3-2. Installing the Switch in a Rack

3.If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, mount them in the rack, one below the other, in any order.

3-4

Image 42

SMC Networks SMC6724L3 INT manual Attaching the Brackets

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA Compliances FCC Class aIndustry Canada Class a EC Conformance Declaration Class a Japan Vcci Class a Australia AS/NZS 3548 1995 Class a Safety Compliance Warnhinweis Faseroptikanschlüsse Optische SicherheitUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Viii Table of Contents Installing the Switch Making Network Connections Appendices Table of Contents Chapter About Tigerswitch 10/100 Overview Switch Architecture SMC6724L3 Front and Rear Panels Management Options Description of Hardware RJ-45 Ports Ports Status LEDs Port Status LEDs System Status LEDs System Status LEDs Optional Media Extender Modules Optional 10/100/1000BASE-T Module SMC6824GTOptional 100BASE-FX Module SMC6824FSSC Optional 100BASE-FX Module SMC6824FMSC Optional 1000BASE-X Gbic Module SMC6824GB Optional Redundant Power Unit Power Supply Receptacle Features and Benefits ConnectivityExpandability Performance Management About the Tigerswitch 10/100 Introduction to Switching Chapter Network Planning Application Examples Collapsed Backbone Central Wiring Closet Central Wiring Closet Remote Connection with Fiber Cable Remote Connection with Fiber Cable Making Vlan Connections Making Vlan Connections Using Layer 3 Routing IP Routing for Unicast Traffic Connectivity Rules Mbps Gigabit Ethernet Collision Domain 10/100 Mbps Ethernet Collision Domain Application Notes Network Planning Installing the Switch Selecting a Site Equipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack Mounting Attaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive Feet Installing an Optional Module into the Switch Installing an Optional Module Installing a Gbic Transceiver Installing a Gbic Transceiver Connecting to a Power Source Power Receptacle Twisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair Connections TWISTED-PAIR Devices Wiring Closet Connections Wiring Closet Connections Fiber Optic Devices Making SC Port Connections Appendix a Troubleshooting Diagnosing Switch Indicators Power and Cooling Problems InstallationIn-Band Access Specifications Appendix B Cables Twisted-Pair Cable and Pin Assignments Fiber SMF Figure B-1. RJ-45 Connector Pin Numbers 10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring Crossover Wiring 1000BASE-T Pin Assignments Cable Testing for Existing Category 5 Cable Adjusting Existing Category 5 Cabling1000BASE-T Cable Requirements Wiring Map for Serial Cable Console Port Pin Assignments Cables Appendix C Specifications Physical CharacteristicsBase Unit Compliances Warranty Slide-in Modules100BASE-FX Extender Modules 1000BASE-T Extender Module Model 1000BASE-X Gbic Module Specifications Appendix D Ordering Information Ordering Information Glossary 1000BASE-T Collision Auto-NegotiationBandwidth Collision Domain Full Duplex Fast Ethernet SwitchFast Ethernet Gigabit Ethernet LAN Segment Media Access Control MACIeee 802.3z Link Segment RJ-45 Connector Switched PortsStraight-through Port Glossary-6 Index Numerics Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call