TWISTED-PAIR Devices | SMC Networks SMC6724L3 INT guide

TWISTED-PAIR DEVICES

2.If the device is a PC card and the switch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet. (See “Wiring Closet Connections” on the next page.) Otherwise, attach the other end to an available port on the switch.

3.Make sure each twisted pair cable does not exceed 100 meters (328 ft) in length.

Note: When connected to a shared collision domain (such as a hub with multiple workstations), switch ports must be set to half-duplex mode.

4.As each connection is made, the Link LED (on the switch) corresponding to each port will light to indicate that the connection is valid.

4-3

Image 49

SMC Networks SMC6724L3 INT manual TWISTED-PAIR Devices

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA FCC Class a CompliancesIndustry Canada Class a EC Conformance Declaration Class a Japan Vcci Class a Australia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Viii Table of Contents Making Network Connections Installing the Switch Appendices Table of Contents Overview Chapter About Tigerswitch 10/100 SMC6724L3 Front and Rear Panels Switch Architecture Management Options RJ-45 Ports Description of Hardware Port Status LEDs Ports Status LEDs System Status LEDs System Status LEDs Optional 10/100/1000BASE-T Module SMC6824GT Optional Media Extender ModulesOptional 100BASE-FX Module SMC6824FSSC Optional 1000BASE-X Gbic Module SMC6824GB Optional 100BASE-FX Module SMC6824FMSC Power Supply Receptacle Optional Redundant Power Unit Connectivity Features and BenefitsExpandability Management Performance About the Tigerswitch 10/100 Chapter Network Planning Introduction to Switching Collapsed Backbone Application Examples Central Wiring Closet Central Wiring Closet Remote Connection with Fiber Cable Remote Connection with Fiber Cable Making Vlan Connections Making Vlan Connections IP Routing for Unicast Traffic Using Layer 3 Routing Mbps Gigabit Ethernet Collision Domain Connectivity Rules 10/100 Mbps Ethernet Collision Domain Application Notes Network Planning Selecting a Site Installing the Switch Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting Mounting Attaching the Brackets Attaching the Adhesive Feet Desktop or Shelf Mounting Installing an Optional Module Installing an Optional Module into the Switch Installing a Gbic Transceiver Installing a Gbic Transceiver Power Receptacle Connecting to a Power Source Chapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Cabling Guidelines Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and Switches TWISTED-PAIR Devices Wiring Closet Connections Wiring Closet Connections Fiber Optic Devices Making SC Port Connections Diagnosing Switch Indicators Appendix a Troubleshooting Installation Power and Cooling ProblemsIn-Band Access Appendix B Cables Specifications Fiber SMF Twisted-Pair Cable and Pin Assignments 10BASE-T/100BASE-TX Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers Crossover Wiring Straight-Through Wiring 1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements Console Port Pin Assignments Wiring Map for Serial Cable Cables Physical Characteristics Appendix C SpecificationsBase Unit Compliances Slide-in Modules Warranty100BASE-FX Extender Modules Model 1000BASE-T Extender Module 1000BASE-X Gbic Module Specifications Appendix D Ordering Information Ordering Information 1000BASE-T Glossary Bandwidth Auto-NegotiationCollision Collision Domain Fast Ethernet Fast Ethernet SwitchFull Duplex Gigabit Ethernet Ieee 802.3z Media Access Control MACLAN Segment Link Segment Switched Ports RJ-45 ConnectorStraight-through Port Glossary-6 Numerics Index Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call