Compliances, FCC Class a | SMC Networks SMC6724L3 INT specification

COMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45 connections—Category 3 or greater for 10 Mbps connections, Category 5 for 100 Mbps connections, and Category 5, 5e, or 6 for 1000 Mbps. Use 50/125 or 62.5/125 micron multimode fiber optic cable, or 9/125 micron single-mode fiber optic cable, for SC or ST-type connections.

Warnings: 1. Wear an anti-static wrist strap or take other suitable measures to prevent electro- static discharge when handling this equipment.

2.When connecting this switch to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.

iii

Image 7

SMC Networks SMC6724L3 INT manual Compliances, FCC Class a, Industry Canada Class a

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA FCC Class a CompliancesIndustry Canada Class a EC Conformance Declaration Class a Japan Vcci Class a Australia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Viii Table of Contents Making Network Connections Installing the Switch Appendices Table of Contents Overview Chapter About Tigerswitch 10/100 SMC6724L3 Front and Rear Panels Switch Architecture Management Options RJ-45 Ports Description of Hardware Port Status LEDs Ports Status LEDs System Status LEDs System Status LEDs Optional 10/100/1000BASE-T Module SMC6824GT Optional Media Extender ModulesOptional 100BASE-FX Module SMC6824FSSC Optional 1000BASE-X Gbic Module SMC6824GB Optional 100BASE-FX Module SMC6824FMSC Power Supply Receptacle Optional Redundant Power Unit Connectivity Features and BenefitsExpandability Management Performance About the Tigerswitch 10/100 Chapter Network Planning Introduction to Switching Collapsed Backbone Application Examples Central Wiring Closet Central Wiring Closet Remote Connection with Fiber Cable Remote Connection with Fiber Cable Making Vlan Connections Making Vlan Connections IP Routing for Unicast Traffic Using Layer 3 Routing Mbps Gigabit Ethernet Collision Domain Connectivity Rules 10/100 Mbps Ethernet Collision Domain Application Notes Network Planning Selecting a Site Installing the Switch Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting Mounting Attaching the Brackets Attaching the Adhesive Feet Desktop or Shelf Mounting Installing an Optional Module Installing an Optional Module into the Switch Installing a Gbic Transceiver Installing a Gbic Transceiver Power Receptacle Connecting to a Power Source Cabling Guidelines Connecting Network DevicesChapter Making Network Connections Twisted-Pair Devices Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and Switches TWISTED-PAIR Devices Wiring Closet Connections Wiring Closet Connections Fiber Optic Devices Making SC Port Connections Diagnosing Switch Indicators Appendix a Troubleshooting Installation Power and Cooling ProblemsIn-Band Access Appendix B Cables Specifications Fiber SMF Twisted-Pair Cable and Pin Assignments 10BASE-T/100BASE-TX Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers Crossover Wiring Straight-Through Wiring 1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements Console Port Pin Assignments Wiring Map for Serial Cable Cables Physical Characteristics Appendix C SpecificationsBase Unit Compliances Slide-in Modules Warranty100BASE-FX Extender Modules Model 1000BASE-T Extender Module 1000BASE-X Gbic Module Specifications Appendix D Ordering Information Ordering Information 1000BASE-T Glossary Collision Domain Auto-NegotiationBandwidth Collision Gigabit Ethernet Fast Ethernet SwitchFast Ethernet Full Duplex Link Segment Media Access Control MACIeee 802.3z LAN Segment Switched Ports RJ-45 ConnectorStraight-through Port Glossary-6 Numerics Index Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call