Making SC Port Connections | SMC Networks SMC6724L3 INT specification

MAKING NETWORK CONNECTIONS

3.Connect one end of the cable to the SC port on the switch and the other end to the SC port on the other device. Since SC connectors are keyed, the cable can be attached in only one orientation.

SC fiber connector

Figure 4-3. Making SC Port Connections

4.As a connection is made, check the Activity LED on the switch’s front panel for the corresponding module to be sure that the connection is valid.

Note: If you use the optional SC-ST Converter, be sure to connect the converter’s Tx (Rx) port to the Rx (Tx) port on the other device.

4-6

Image 52

SMC Networks SMC6724L3 INT manual Making SC Port Connections

Contents

TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty SMC Networks, Inc Tesla Irvine, CA FCC Class a CompliancesIndustry Canada Class a EC Conformance Declaration Class a Japan Vcci Class a Australia AS/NZS 3548 1995 Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceUnderwriters Laboratories Compliance Statement Wichtige Sicherheitshinweise Germany Viii Table of Contents Installing the Switch Making Network Connections Appendices Table of Contents Chapter About Tigerswitch 10/100 Overview Switch Architecture SMC6724L3 Front and Rear Panels Management Options Description of Hardware RJ-45 Ports Ports Status LEDs Port Status LEDs System Status LEDs System Status LEDs Optional 10/100/1000BASE-T Module SMC6824GT Optional Media Extender ModulesOptional 100BASE-FX Module SMC6824FSSC Optional 100BASE-FX Module SMC6824FMSC Optional 1000BASE-X Gbic Module SMC6824GB Optional Redundant Power Unit Power Supply Receptacle Connectivity Features and BenefitsExpandability Performance Management About the Tigerswitch 10/100 Introduction to Switching Chapter Network Planning Application Examples Collapsed Backbone Central Wiring Closet Central Wiring Closet Remote Connection with Fiber Cable Remote Connection with Fiber Cable Making Vlan Connections Making Vlan Connections Using Layer 3 Routing IP Routing for Unicast Traffic Connectivity Rules Mbps Gigabit Ethernet Collision Domain 10/100 Mbps Ethernet Collision Domain Application Notes Network Planning Installing the Switch Selecting a Site Package Contents Equipment ChecklistOptional Rack-Mounting Equipment Mounting Rack Mounting Attaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive Feet Installing an Optional Module into the Switch Installing an Optional Module Installing a Gbic Transceiver Installing a Gbic Transceiver Connecting to a Power Source Power Receptacle Connecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling Guidelines Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair Connections TWISTED-PAIR Devices Wiring Closet Connections Wiring Closet Connections Fiber Optic Devices Making SC Port Connections Appendix a Troubleshooting Diagnosing Switch Indicators Installation Power and Cooling ProblemsIn-Band Access Specifications Appendix B Cables Twisted-Pair Cable and Pin Assignments Fiber SMF Figure B-1. RJ-45 Connector Pin Numbers 10BASE-T/100BASE-TX Pin Assignments Straight-Through Wiring Crossover Wiring 1000BASE-T Pin Assignments Adjusting Existing Category 5 Cabling Cable Testing for Existing Category 5 Cable1000BASE-T Cable Requirements Wiring Map for Serial Cable Console Port Pin Assignments Cables Physical Characteristics Appendix C SpecificationsBase Unit Compliances Slide-in Modules Warranty100BASE-FX Extender Modules 1000BASE-T Extender Module Model 1000BASE-X Gbic Module Specifications Appendix D Ordering Information Ordering Information Glossary 1000BASE-T Auto-Negotiation BandwidthCollision Collision Domain Fast Ethernet Switch Fast EthernetFull Duplex Gigabit Ethernet Media Access Control MAC Ieee 802.3zLAN Segment Link Segment Switched Ports RJ-45 ConnectorStraight-through Port Glossary-6 Index Numerics Index-2 Index-3 Index-4 Page For Technical SUPPORT, Call