DME Switcher Introduction
Procedure
6 In the numeric keypad, press buttons 1, 1, 0, 0, in that order. |
The TRANS RATE display window shows “1.1.0.0.”. |
Chapter 3 Basic Operation
<Preparation>
<Image selection>
<Effect selection>
|
|
|
|
|
| 8 |
|
|
|
|
|
|
|
|
|
|
| 5 |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| USER PGM | SNAP SHOT |
|
|
|
| |
|
| 1 TITLE 2 | DSK | EDGE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| STATUS EDIT |
|
|
|
|
|
|
| EDITOR | LUM | LUM | LUM | TRAIL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SHADOW |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| GPI | CRK | CRK | BORDER | BEVELD |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| EDGE |
| INITIAL |
|
|
|
|
|
|
| EDIT | LEARN |
|
|
|
|
|
| SET UP | MASK | MASK | MASK | SOFT |
|
|
|
|
|
|
|
|
|
| RECALL |
|
|
|
|
|
2 | SHIFT | CCR | LIGHTING MATTES | BORDER |
| PATTERN | PAGE | F1 |
| F2 | F3 | F4 | F5 |
| HOLD |
| LOCATION |
|
| ||
|
|
|
|
|
| ADJ |
|
|
|
|
|
|
|
| INPUT |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| EFFECT |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| TRANS RATE |
|
| DSK |
| PATTERN NUMBER |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| FTB | SET |
|
|
|
| SET |
|
| |
|
|
| CCR | TITLE 1 | TITLE 2 | DSK | SUPER BG FRGD 2 | MEMORY | FRAME | FREEZ | MIX | EFFECT |
|
| N/R | REV | DIRECT | DIRECT | DSK PVW |
| |
| AUXILIARY |
| SOURCE | SOURCE | FILL |
|
|
|
|
|
|
|
|
|
|
| RECALL PATTERN |
|
| ||
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LAST X | FADE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 7 | 8 | 9 |
| TO | 6 | |
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT |
| TITLE |
|
| INS | BLACK | |||||
BACKGROUND |
|
|
|
|
|
|
|
| VIDEO |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT | CUT |
|
| 4 | 5 | 6 | DEL |
| |||
| VIDEO |
|
| 1 | 2 | 3 | P IN P | DSK | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RST |
| 7 | |||
| FOREGROUND |
|
|
|
|
|
|
|
|
|
|
|
|
| DOWN | UP | ENTER |
| |||
| BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT | AUTO |
|
| 0 |
|
|
|
| ||
| VIDEO | TRANS |
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| PATTERN/KEY PAD |
|
|
4
1,9
1 Pull the fader lever toward you as far as it will go.
2 Press the MATTES button in the menu control section, and display page 1 of the MATTE menu, then with the F1(SELECT) button select “INT V”.
MATTE | SELECT | Lum | Sat | Hue | CH2BRD |
1/2 | INT V | BRDMAT | |||
PAGE | F1 | F2 | F3 | F4 | F5 |
You can change the color of matte color and embossing pattern. For details, see the section “Adjusting Color Mattes” (page
3 Press the BACKGROUND bus INT VIDEO button.
The pressed button lights red, and a color matte is selected as the background image.
4 Press the FOREGROUND bus button 1.
The pressed button lights amber, and the video signal connected to the VIDEO INPUT 1 connector is selected as the foreground image.
5 Press the SET button to the right of the PATTERN NUMBER display window, turning it on.
(If it is already lit, omit this step.)
<Border settings>
<Effect execution>
| Dots appear to the lower right of the digits. |
|
7 | Press the ENTER button. |
|
| The dots to the lower right of the digits disappear, and |
|
| picture, or pattern number 1100, is selected. |
|
8 | In the menu control section, press the BORDER button. |
|
| The button lights, enabling the border. |
|
| You can change the color and width of the border. For details, see the section | Chapter 3 |
| “Modifying the Boundary” (page | |
9 |
| |
Move the fader lever to the opposite end. | Basic | |
|
| |
| Both the BACKGROUND bus INT VIDEO button and the | Operation |
|
|
FOREGROUND bus button 1 light red.
As you move the lever, the
1- | ||
17 | ||
|
Chapter 3 Basic Operation |