1-26
Selecting an Effect
Selection in Pattern Number Specification Mode
In the pattern number specification mode, you select the desired effect pattern by entering the number.
Procedure
To select an effect pattern in the pattern number specification mode, use the following procedure.
Note
If the EDIT button in the user program section (see page
If you enter a wrong number
Before pressing the ENTER button press the P IN P/RST button to cancel the wrong number, then enter the correct number.
Note
If you enter an invalid number (a number with no corresponding pattern), this is automatically corrected to the closest valid number larger than the number you entered. However, if you enter a number larger than 9309 this is corrected to pattern number 0001.
Adjusting the number before confirming
To increment the number by one, press the UP button. Hold down the UP button to increase the number continuously.
To decrement the number by one, press the DOWN button. Hold down the DOWN button to decrease the number continuously.
Chapter 3 Basic Operation
| 1 TITLE 2 | DSK | EDGE |
|
|
|
|
|
|
|
|
| |
EDITOR | LUM | LUM | LUM | TRAIL |
|
|
|
|
|
|
|
|
|
|
|
|
| SHADOW |
|
|
|
|
|
|
|
|
|
GPI | CRK | CRK | BORDER | BEVELD |
|
|
|
|
|
|
|
|
|
|
|
|
| EDGE |
| INITIAL |
|
|
|
|
|
|
|
SET UP | MASK | MASK | MASK | SOFT |
|
|
|
|
|
|
|
|
|
SHIFT | CCR | LIGHTING MATTES | BORDER |
| PATTERN | PAGE | F1 |
| F2 | F3 | F4 | F5 | |
|
|
|
|
|
| ADJ |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| EFFECT |
|
|
|
|
|
|
|
|
| TRANS RATE |
|
| DSK |
| |
|
|
|
|
|
|
|
|
|
|
|
| FTB | SET |
|
| CCR | TITLE 1 | TITLE 2 | DSK | SUPER BG FRGD 2 | MEMORY | FRAME | FREEZ | MIX | EFFECT |
| |
AUXILIARY |
| SOURCE | SOURCE | FILL |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT |
| TITLE |
|
BACKGROUND |
|
|
|
|
|
|
|
| VIDEO |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT | CUT |
| |
VIDEO |
| ||||||||||||
FOREGROUND |
|
|
|
|
|
|
|
|
|
|
|
| |
BLACK | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | MEMORY | INT | AUTO |
| |
VIDEO | TRANS |
| |||||||||||
1 Press the SET button, turning it on.
USER PGM | SNAP SHOT |
|
|
| |
STATUS EDIT |
|
|
|
|
|
EDIT | LEARN |
|
|
|
|
| RECALL |
|
|
|
|
| HOLD |
| LOCATION |
| |
| INPUT |
|
|
|
|
PATTERN NUMBER |
|
|
|
| |
|
|
|
| SET |
|
| N/R | REV | DIRECT | DIRECT | DSK PVW |
|
|
| RECALL PATTERN |
| |
|
|
|
| LAST X | FADE |
| 7 | 8 | 9 |
| TO |
| INS | BLACK | |||
| 4 | 5 | 6 | DEL |
|
|
|
|
| P IN P | DSK |
| 1 | 2 | 3 | RST |
|
DOWN UP ENTER
0
PATTERN/KEY PAD
1
2
3
Chapter 3 Basic Operation
2 Enter the desired pattern number using buttons 0 to 9 on the pattern/ numeric keypad.
The number you entered appears in the PATTERN NUMBER display window. Dots appear at the lower right of each digit, indicating that the entry is not yet confirmed.
3 Press the ENTER button.
The dots to the lower right of the digits in the PATTERN NUMBER display window disappear, confirming the pattern number.
Chapter 3 Basic Operation
