Sony DSR-DR1000A, DSR-DR1000AP manual 31

When controlling this unit from an editing control unit				Video input signal		Corresponding	Lit indicator
connected to the REMOTE IN (R)connector, see “Control				(input connector)		INPUT	in the INPUT
mode selector” on page 11 and the description of the						SELECT	signal display
REMOTE I/F menu item on page 69.						button	section
1 Power on the video monitor, then set its input				SDI signal		VIDEO	SDI in VIDEO
				(SDI IN)			group
	switches according to the signals input from the			i.LINK-compatible		VIDEO	i.LINK
	player.			digital video signal in
2 Set up the player to play back a tape.				DV format
				( S400(i.LINK))
	For details, refer to the operating instructions for the			Internal test video		VIDEO	SG in VIDEO
				signal			group
	player.
3 Power on this unit by pressing the 1 switch on the
				Audio input signal		Corresponding	Lit indicator
				(input connector)		INPUT SELECT	in the INPUT
	front panel.					button	signal display
4 When the REMOTE indicator is off (the external							section
				Analog signal		CH1 1/2 and	ANALOG in
	editing control unit is not used), use the COUNTER			(AUDIO IN 1/3 and		CH2 3/4	AUDIO group
	SELECT button to select the type of time data to be			AUDIO IN 2/4)
	used.
				AES/EBU signal		CH1 1/2 and	AES/EBU in
	Each press of this button cycles through three options:			(AUDIO (AES/EBU)		CH2 3/4	AUDIO group
				IN)
	COUNTER (CNT value), TC (time code), and U-BIT
				SDI signal		CH1 1/2 and	SDI in AUDIO
	(user bit data). The time data type indicator for each
				(SDI IN)		CH2 3/4	group
	option lights as it is selected.
				i.LINK-compatible		automatic	i.LINK
				digital audio signal in		setting
	Selected time data	Time data type indicator
				DV format		depending on
	Count value of the time	COUNTER		( S400(i.LINK))		video input
	counter					signals
	Time code	TC		Internal test audio		CH1 1/2 and	SG in AUDIO
				signal		CH2 3/4	group
	User bit data	U-BIT
	When the REMOTE indicator is lit, selection of the
				Caution
	time data type is carried out at the editing control unit.			Once you	have started recording, you cannot change
5 Select the formats of video and audio input signal to				the input signal selection.
			6 Select the audio mode.
	be recorded.
	Use the INPUT SELECT buttons in the video/audio			Select either two-channel mode (2 CHANNEL) or
	input setting section to select the desired signal
	formats. Each selection is shown by a lit indicator in			four-channel mode (4 CHANNEL) with the REC
	the INPUT signal display section.			MODE menu item (see page 68). The corresponding
				indicator lights in the REC MODE display.

Playback and Recording 3 Chapter

Video input signal	Corresponding	Lit indicator
(input connector)	INPUT	in the INPUT
	SELECT	signal display
	button	section
Composite signal	VIDEO	COMPOSITE
(VIDEO IN: Y/CPST)		in VIDEO
		group
Separated Y/C	VIDEO	S VIDEO in
signal		VIDEO group
(VIDEO IN: Y/CPST
and R−Y/S−C)
Component signal	VIDEO	Y−R,B in
(VIDEO IN: Y/CPST,		VIDEO group
R−Y/S−C, and B−Y/
S−Y)

Audio mode	Lit indicator in the REC MODE
	display
2-channel mode	2CH
4-channel mode	4CH

Cautions

•Two audio recording modes, with either two channels at 48 kHz or four channels at 32 kHz, can be used on this unit. It is not possible to select any other mode (for example with four channels at 48 kHz).

•If there is a point where the audio mode is switched, it is not possible to carry out insert editing over a section including that point.

Recording 31