Manuals / Brands / TV and Video / DVD Recorder / Sony / TV and Video / DVD Recorder

Sony DSR-DR1000A, DSR-DR1000AP Changing Menu Settings, Buttons Used to Change Settings, Changing the Settings of Basic Items

1 105

Download 105 pages, 2.07 Mb

Setting Menu 6 Chapter

VIDEO OUTPUT PHASE mode

The time code output signal is synchronized with the output video signal.

This mode is appropriate when outputting signals from a single device to a number of recorders using separate cables for video, audio, and time code.

In this mode, the same time code is recorded on all of the recorders 1 to n.

VIDEO OUT									VIDEO IN


AUDIO OUT									VIDEO OUT


TIME CODE OUT									AUDIO IN


									AUDIO OUT
									AUDIO OUT
									TIME CODE IN
Output device									TIME CODE IN
Output device									TIME CODE OUT
(VCR, camera, etc.)									TIME CODE OUT
(VCR, camera, etc.)
							DSR-DR1000A/DR1000AP
							(1st unit)

VIDEO IN

VIDEO OUT

AUDIO IN

AUDIO OUT

TIME CODE IN

TIME CODE OUT

DSR-DR1000A/DR1000AP (2nd unit)

VIDEO IN

VIDEO OUT

AUDIO IN

AUDIO OUT

TIME CODE IN

TIME CODE OUT

DSR-DR1000A/DR1000AP (nth unit)

• Composite video signal

•S-video signal

•Analog component signal

•SDI (video and audio) signal

Audio signal

Time code signal

Changing Menu Settings

This section explains how to change menu settings.

Buttons Used to Change Settings

Use the following buttons in the menu control section to change the menu settings.

Menu control buttons	Functions

MENU button	• Opens the menu and
		launches menu control
		mode.
	• Closes the menu and exits
		menu control mode.

J (CUE) and j buttons	These buttons move the
	highlighted cursor up and
	down within the current level
	to select an item or setting.
	Hold down one of these
	buttons to make the
	highlighted cursor move
	continuously.

K (IN) and k (OUT)	•	Press the k (IN) button
buttons		to go up one level.
	•	Press the K (OUT)
		button to go down one
		level.
	Hold down one of these
	buttons to make the
	highlighted cursor move
	continuously.

RESET button	•	Returns the setting to the
		factory default setting.
	•	Sends a negative
		response to prompts on
		the monitor screen.

SET button	•	Saves the new setting in
		memory.
	• Sends a positive response
		to prompts on the monitor
		screen.

Changing the Settings of Basic Items

The factory default setting is to display only the basic items. To change the settings of basic items proceed as follows.

72 Changing Menu Settings

Contents

Operating Instructions DSR-DR1000A/DR1000AP Owner’s Record Important Safety Instructions WARNING THIS APPARATUS MUST BE EARTHED Page Table of Contents Chapter Clip Operations Network Operations Chapter 6 Menu Setting Chapter 7 Connections and Settings Chapter 8 Maintenance and Troubleshooting Appendixes Overview Chapter Features Compact Size Facilities for High-EfficiencyEditing 200% variable playback Digital jog sound function Video process control Simultaneous recording and playback Program playback (clip segment playback) Multi-simultaneousplayback (9-pin(PARA) function) Other Features Support for two i.LINK protocols Location and Function of Parts Page Page 1Display section Page 2Video/audio input setting section 3Audio input/output level control section 4Recording/playback control section 5PANEL SELECT section 6Menu/clip control section 7Search control section Rear Panel 1Analog video/audio signal input section 2Analog video/audio signal output section 3Digital signal input/output section DTime code input/output section Preparations Chapter Setting the Date and Time Setting the Time Data Displaying Time Data and Operation Mode Indications To view time data and operation mode indications on the monitor screen F Recording indications during simultaneous playback and recording To set the initial time code value and user bit data 2,3 6 1 4,5,6 Advancement of internal time code generator To set the current time as the initial time code value Synchronizing Internal and External Time Codes To synchronize the internal time code to external time code To confirm external synchronization Making Basic Network Settings Recording and Playback Chapter Recording Page Recording Procedure To Set Cue Points Long-timeRecording With Video Camera Playback Recording and Playing Back Simultaneously To play back during recording To start and stop recording during playback To set a cue point during simultaneous recording and playback To select output signals during simultaneous recording and playback Setting Points A and B for Repeat Playback Inputting time code values for points A and Setup menu Operational >REP FUNC >> REPEAT MD >> REP TOP >>> VD top >>> A point >> A preset Repeat Playback —AutomaticCyclical Playback High-Speedand Low-SpeedSearch —Quicklyand Accurately Determining Editing Points Searching with the NEXT and PREV buttons Searching with the search dial Cueing Up a Desired Cue Point Clip Operations Chapter Clips To Search in Clip Units (Clip Jump) Playing Back Scenes Extracted From Clips (Program Playback) Working with Playlists To reset In and Out points To add a new scene To change the playback order of the scenes To delete scenes Saving the Current Playlist Data To Delete a Playlist Exiting the Clip Menu Network Operations Chapter Connecting This Unit to a LAN Network Menu Net menu Creating and Editing an Address Book Adrs Book >--END >01HOST1 Editing an Address Book To delete a host entry To change a host entry To delete all of the entries in an address book Sending Data >Clip Clip >Cliplist >Cliplist1 >Adrs Book Receiving Data Receive Saving or Deleting Received Data New Content Status Page Menu Setting Chapter Menu Organization Page Page Menu Contents Page Page Page Page Page Page Page Page EEOUT PHASE settings for time code output Page Changing Menu Settings Display > Chara disp > Brightness Meanings of indications on the monitor screen Displaying Enhanced Items Changing the Settings of Enhanced Items Menu grade Displaying Supplementary Status Information Page Connections and Settings Chapter Connections With Camera System (Event Recording) Connections to a Digital Non-LinearEditing System Connections for a Cut Editing System Settings on this unit (player) About reference video signals Connections for an A/B Roll Editing System Page Audio monitor system connections Reference video signal connection Control signal connections Video/audio signal connections Connection of a video monitor Settings on an editing control unit Adjusting the Sync and Subcarrier Phases Page Maintenance and Troubleshooting Chapter Regular Checks Oper Play Rec Troubleshooting ErrorXX-XXX REMOTE Page Page Appendixes Precautions Specifications Audio performance Input connectors Output connectors Remote control connectors Accessories supplied Accessories not supplied Glossary Page Index