Menu items in the range 800 to 899, relating to audio control

Item number

Item name

Settings

 

 

 

 

 

 

 

 

 

 

801

 

DIGITAL JOG SOUND

Turns the digital jog sound on and off.

 

 

 

 

OFF: Digital jog sound is turned off.

 

 

 

 

Audio of digital channels not subjected to speed correction is output. When the

 

 

 

 

tape stops, after one second the audio is muted.

 

 

 

 

ON

: Digital jog sound is turned on.

 

 

 

 

When the tape speed is in the range ⋅–1 to ⋅+1 (for Betacam SX playback, in the

 

 

 

 

range ⋅–1 to ⋅+2), speed correction is carried out, and the same jog sound as a

 

 

 

 

conventional analog VTR is output.

802

 

DIGITAL AUDIO MUTING

Set the digital audio muting conditions during shuttle playback.

 

 

IN SHUTTLE MODE

 

 

: Not muted.

 

 

OFF

 

 

 

 

CUEUP: Muted during cue-up or preroll operations.

 

 

 

 

FULL: Muted in shuttle mode.

 

 

 

 

 

 

 

 

 

805

 

AUDIO MONITOR

Select the audio mixing method used for digital audio signals and Betacam

 

 

OUTPUT MIXING

playback analog audio signals supplied to the MONITOR OUTPUT connector.

 

 

 

 

ADD: Simple addition

 

 

 

 

RMS

: Root-mean-square

 

 

 

 

AVE: Simple average

 

 

 

 

 

 

 

 

806

 

LEVEL METER SCALE

Select the mode in which digital audio levels are displayed.

 

 

 

 

PEAK0

: Displays the audio level as negative values with the maximum level set

 

 

 

 

to 0 dB.

 

 

 

 

REF.0: Displays the audio level as positive and negative values with the

 

 

 

 

reference level set to 0 dB.

 

 

 

 

 

 

 

807

 

AUDIO OUTPUT PHASE

Select the output timing of digital audio playback signals (HDSDI, SDI, and AES/

 

 

 

 

EBU only). The reference position corresponds to a setting of 80H; when the

 

 

 

 

setting is less than 80H, the output timing is advanced, and when it is higher than

 

 

 

 

80H, the output timing is delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1

 

 

 

 

sample=approx. 20 µs)

 

 

 

 

0 to 80 to FF : Setting in this range

 

 

 

 

 

 

 

808

 

INTERNAL AUDIO

Select the operation of the internal audio test signal generator.

 

 

SIGNAL GENERATOR

 

: No operation

 

 

OFF

 

 

 

 

SILNC: Silent signal

 

 

 

 

1KHZ: At 1 kHz, –20 dB FS sine wave is supplied to all audio input channels.

 

 

 

 

 

 

809

 

AUDIO LEVEL METER

Set the brightness of the audio level meters.

 

 

DIMMER CONTROL

0 to 7: Set in this range. 0 is the brightest, and 7 the dimmest.

 

 

 

 

823

 

NON-AUDIO FLAG PB

Controls the non-audio flag when the playback format is Digital Betacam or

 

 

(Invalid in 24PsF or

Betacam SX.

 

 

23.98PsF mode.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sub-item

 

 

 

 

 

 

 

 

1

CH1/CH2

During playback (except E-E mode), sets the digital audio non-audio flag as

 

 

 

 

follows.

 

 

2

CH3/CH4

 

 

 

 

 

 

 

 

 

 

 

 

OFF

: OFF (the data is audio)

 

 

 

 

ON:

ON (the data is non-audio)

 

 

 

 

AUTO: As follows, depending on whether tape data has been confirmed.

 

 

 

 

• Tape data has been read and confirmed: ON or OFF, according to the data.

 

 

 

 

• Tape data has not been confirmed: Current state is maintained.

 

 

 

 

 

 

 

 

 

Notes

 

 

 

 

 

• In the Betacam SX format, audio signals only are recorded. Therefore, the non-

 

 

 

 

audio flag is OFF.

 

 

 

 

• During playback of analog tapes, the non-audio flag is OFF regardless of the

 

 

 

 

setting of this item.

 

 

 

 

• In the MPEG IMX format, the non-audio flag follows the setting of maintenance

 

 

 

 

menu item M372 during recording, playback, and E-E mode.

 

 

 

 

For more information about the maintenance menu item M372, refer to the

 

 

 

 

Maintenance Manual.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Continued)

Chapter9 SetupMenus

Chapter 9 Setup Menus 9-23