Battery operation time1)

Batteries

Recording2)

Playback

Two NC-AA

Approx.

Approx.

nickel-cadmium

3 hours

5 hours

rechargeable batteries

 

 

 

 

 

Two LR6 (size AA)

3)

Approx.

––––

Sony alkaline dry batteries

 

13 hours

 

 

 

1)The battery life may be shorter due to operating conditions and the temperature

of the location.

2)When you record, use fully charged rechargeable batteries.

3)Recording time may differ according to the alkaline batteries.

Dimensions

Approx. 116.8 × 18.5 × 86.1 mm (w/h/d) (4 5/8 × 3/4 × 3 1/2 in.)

Mass

Approx. 160 g (5.6 oz) the recorder only Approx. 220 g (7.8 oz) incl. a recordable MD, and two NC-AA nickel-cadmium rechargeable batteries

Supplied accessories

Optical cable (1) (MC-918)

AC power adaptor (1) (AC-MZR37)

Headphones with a remote control (1) (SZR-S17)

NC-AA nickel-cadmium rechargeable batteries (2)

Rechargeable battery carrying case (1)

Design and specifications are subject to change without notice.

Precautions for Laser Diode Emission Check

When checking the emission of the laser diode during adjust- ments, never view directly downwards as this may lead to blindness.

Precautions for Using Optical Pick-up (KMS-280A)

As the laser diode inside the optical pick-up damages by static electricity easily, solder the laser tap of the Optical pick-up flexible board when handling. Also take the necessary measures to prevent damages by static electricity. Handle the Optical pick- up flexible board with care as it breaks easily.

This MiniDisc player is classi- fied as a CLASS 1 LASER product.

The CLASS 1 LASER PRODUCT label is located on the bottom exterior.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR CONSEQUENTIAL

DAMAGES OF ANY NATURE, OR

LOSSES OR EXPENSES RESULTING

FROM ANY DEFECTIVE PRODUCT

OR THE USE OF ANY PRODUCT.

“MD WALKMAN” is a trademark of Sony Corporation.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Flexible Circuit Board Repairing

Keep the temperature of the soldering iron around 270°C during repairing.

Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

Be careful not to apply force on the conductor when soldering or unsoldering.

Notes on chip component replacement

Never reuse a disconnected chip component.

Notice that the minus side of a tantalum capacitor may be damaged by heat.

Laser tap

Optical Pick-up flexible board

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINE WITH MARK !ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE !SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

– 2 –

Page 2
Image 2
Sony MZ-R37 specifications Flexible Circuit Board Repairing, Battery operation time1